原始启动log&新log

root@Taiyear:/#

U-Boot 1.1.3 (Dec 27 2013 - 09:14:28)

SoC:MediaTek MT7620

DRAM: Memory Testing..65536K OK. is 64 MB

relocate_code Pointer at: 83fac000

enable ephy clock...done. rf reg 29 = 5

SSC disabled.

spi_wait_nsec: 14

spi device id: ef 40 18 0 0 (40180000)

Flash: W25Q128BV

*** Warning - bad CRC, using default environment

_______________________________________________________________

| ____ _ ____ |

| | _ \ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ |

| | |_) / _` | '_ \ / _` |/ _ \| '__/ _` | _ \ / _ \ \/ / |

| | __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < |

| |_| \__,_|_| |_|\__,_|\___/|_| \__,_|____/ \___/_/\_\ |

| |

| Ralink/MTK SDK Plantform |

| Board:ZBT WR8305RT |

| |

| lintel<lintel.huang@gmail.com> |

|______________________________________________________________|

===============System Info==================

ASIC 7620_MP (Port5<->None)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Flash component: SPI Flash

CPU Speed: 580 MHZ

RAM Size:64 Mbytes

Build Date:Dec 27 2013 Time:09:14:28

============================================

GPIO Init:

UARTF_SHARE_MODE:GPIO

I2C_GPIO_MODE:GPIO

GPIO_MODE_REG:0x1a311d

ReadyLED Bit:0x1

Please choose the operation:

1: Load system code to SDRAM via TFTP.

2: Load system code then write to Flash via TFTP.

3: Boot system code via Flash (default).

4: Entr boot command line interface.

7: Load Boot Loader code then write to Flash via Serial.

9: Load Boot Loader code then write to Flash via TFTP.

3: System Boot system code via Flash.

Press Reset button enter upgrade mode!

## Booting image at bc050000 ...

Image Name: PandoraBox Linux-3.3.8

Image Type: MIPS Linux Kernel Image (lzma compressed)

Data Size: 993659 Bytes = 970.4 kB

Load Address: 80000000

Entry Point: 80000000

Verifying Checksum ... OK

Uncompressing Kernel Image ... OK

No initrd

## Transferring control to Linux (at address 80000000) ...

## Giving linux memsize in MB, 64

Starting kernel ...

Linux Kernel started...

THIS IS ASIC

[ 0.000000] Linux version 3.3.8 (taiyear@taiyear) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Thu Sep 25 15:12:16 CST 2014

[ 0.000000] Board has DDR2

[ 0.000000] MediaTek MT7620N CPU:580MHz, Bus:193MHz Uart:40MHz

[ 0.000000] Boot form:SPI FLASH

[ 0.000000] MIPS CPU sleep mode enabled.

[ 0.000000] Detecting memory...64 MB!

[ 0.000000] PCIE: bypass PCIe DLL.

[ 0.000000] PCIE: Elastic buffer control: Addr:0x68 -> 0xB4

[ 0.000000] disable all power about PCIe

[ 0.000000] PCIE: PLL power down for MT7620N

[ 0.000000] CPU revision is: 00019650 (MIPS 24KEc)

[ 0.000000] Determined physical RAM map:

[ 0.000000] memory: 04000000 @ 00000000 (usable)

[ 0.000000] Zone PFN ranges:

[ 0.000000] Normal 0x00000000 -> 0x00004000

[ 0.000000] Movable zone start PFN for each node

[ 0.000000] Early memory PFN ranges

[ 0.000000] 0: 0x00000000 -> 0x00004000

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256

[ 0.000000] Kernel command line: console=ttyS1,115200n8 board=TY7620NI rootfstype=squashfs

[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.

[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

[ 0.000000] Writing ErrCtl register=000464a0

[ 0.000000] Readback ErrCtl register=000464a0

[ 0.000000] Memory: 61752k/65536k available (2371k kernel code, 3784k reserved, 393k data, 168k init, 0k highmem)

[ 0.000000] SLUB: Genslabs=9, HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] NR_IRQS:128

[ 0.000000] MTK/Ralink System Tick Counter init... cd:802a47c0, m:214748, s:32

[ 0.000000] console [ttyS1] enabled

[ 0.004000] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)

[ 0.040000] pid_max: default: 32768 minimum: 301

[ 0.044000] Mount-cache hash table entries: 512

[ 0.048000] NET: Registered protocol family 16

[ 0.052000] Ralink/MTK BootROM maped.

[ 0.056000] MIPS: machine is TY-7620N-1

[ 0.060000] Ralink Board GPIO_MODE init:

[ 0.064000] I2C:GPIO

[ 0.064000] SPI_REFCLK:GPIO

[ 0.068000] UART_F:GPIO

[ 0.068000] GPIO_MODE_REGs: 0x1a311d

[ 0.072000] ralink_register_flash:SPI Flash.

[ 0.080000] illegal access irq registered.

[ 0.084000] General GPIO Driver for MediaTek MT7620N Board. Copyright lintel 2005-2013

[ 0.088000] gpiochip_add: registered GPIOs 0 to 23 on device: MT7620-GPIO0

[ 0.092000] gpiochip_add: registered GPIOs 24 to 39 on device: MT7620-GPIO1

[ 0.096000] gpiochip_add: registered GPIOs 40 to 71 on device: MT7620-GPIO2

[ 0.100000] gpiochip_add: registered GPIOs 72 to 95 on device: MT7620-GPIO3

[ 0.200000] MT7620 PPLL unlock

[ 0.212000] bio: create slab <bio-0> at 0

[ 0.216000] Switching to clocksource Ralink external timer

[ 0.220000] NET: Registered protocol family 2

[ 0.224000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.232000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)

[ 0.240000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.248000] TCP: Hash tables configured (established 2048 bind 2048)

[ 0.252000] TCP reno registered

[ 0.256000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[ 0.264000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[ 0.268000] NET: Registered protocol family 1

[ 0.276000] Ralink SoC clocks api init.

[ 0.280000] Ralink GPIODEV resource maped.

[ 0.284000] Load Ralink Timer0 Module

[ 0.288000] Load Ralink Timer1 Module

[ 0.292000] RT3xxx EHCI/OHCI init.

[ 0.312000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[ 0.332000] msgmni has been set to 120

[ 0.336000] io scheduler noop registered

[ 0.340000] io scheduler deadline registered (default)

[ 0.344000] io scheduler cfq registered

[ 0.348000] Ralink DMA Engine API Enable .

[ 0.352000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

[ 0.360000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A

[ 0.368000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A

[ 0.376000] Enable Ralink GDMA Controller Module

[ 0.380000] GDMA IP Version=3

[ 0.388000] loop: module loaded

[ 0.392000] Ralink SPI flash Driver for PandoraBox.

[ 0.400000] deice id : ef 40 18 0 0 (40180000)

[ 0.404000] W25Q128BV(ef 40180000) (16384 Kbytes)

[ 0.408000] mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 65536

[ 0.420000] Creating 5 MTD partitions on "raspi":

[ 0.424000] 0x000000000000-0x000000030000 : "u-boot"

[ 0.428000] 0x000000030000-0x000000040000 : "u-boot-env"

[ 0.436000] 0x000000040000-0x000000050000 : "Factory"

[ 0.444000] 0x000000000000-0x000001000000 : "fullflash"

[ 0.452000] 0x000000050000-0x000001000000 : "firmware"

[ 0.456000] Creating 2 MTD partitions on "raspi":

[ 0.464000] 0x000000050000-0x000000150000 : "kernel"

[ 0.468000] 0x000000150000-0x000001000000 : "rootfs"

[ 0.476000] mtd: partition "rootfs" set to be root filesystem

[ 0.480000] mtd: partition "rootfs_data" created automatically, ofs=4E0000, len=B20000

[ 0.492000] 0x0000004e0000-0x000001000000 : "rootfs_data"

[ 0.500000] rdm_major = 253

[ 0.500000] EEPROM:Read from [Factory] offset 0x28,length 0x6.

[ 0.508000] Ralink APSoC Ethernet Driver v3.0.6. Rx Ring: 256, Tx Ring: 256. Max packet size: 1536.

[ 0.516000] raeth: disable ESW ports on driver init.

[ 0.524000] mt762x-gsw switch driver registered.

[ 0.528000] Ralink APSoC Hardware Watchdog Timer

[ 0.532000] SDHC Interface init.

[ 0.540000] mtk-sd: MediaTek MT76xx MSDC Driver

[ 0.544000] TCP cubic registered

[ 0.548000] NET: Registered protocol family 17

[ 0.552000] 8021q: 802.1Q VLAN Support v1.8

[ 0.564000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.

[ 0.572000] Freeing unused kernel memory: 168k freed

##### MediaTek MT76xx ESW VLAN Partition(LLLLW) #####

switch reg write offset=2004, value=ff0003

switch reg write offset=2104, value=ff0003

switch reg write offset=2204, value=ff0003

switch reg write offset=2304, value=ff0003

switch reg write offset=2404, value=ff0003

switch reg write offset=2504, value=ff0003

switch reg write offset=2010, value=810000c0

switch reg write offset=2110, value=810000c0

switch reg write offset=2210, value=810000c0

switch reg write offset=2310, value=810000c0

switch reg write offset=2410, value=810000c0

switch reg write offset=2510, value=810000c0

switch reg write offset=2610, value=81000000

switch reg write offset=2710, value=81000000

switch reg write offset=2604, value=20ff0003

switch reg write offset=2704, value=20ff0003

Special Tag Disabled

switch reg write offset=2610, value=81000000

switch reg write offset=2014, value=10001

switch reg write offset=2114, value=10001

switch reg write offset=2214, value=10001

switch reg write offset=2314, value=10001

switch reg write offset=2414, value=10002

switch reg write offset=2514, value=10001

REG_ESW_WT_MAC_ATC is 0x7ff0002

done.

- preinit -

Press the [f] key and hit [enter] to enter failsafe mode

- regular preinit -

[ 5.640000] JFFS2 notice: (447) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 1 orphan) and 32 of xref (0 dead, 17 orphan) found.

switching to jffs2

- init -

Please press Enter to activate this console. [ 7.068000] Uniform Multi-Platform E-IDE driver

[ 7.320000] SCSI subsystem initialized

[ 7.456000] usbcore: registered new interface driver usbfs

[ 7.464000] usbcore: registered new interface driver hub

[ 7.472000] usbcore: registered new device driver usb

[ 7.816000] PPP generic driver version 2.4.2

[ 7.852000] gpiodev: gpio device registered with major 254

[ 7.868000] ide-gd driver 1.18

[ 8.440000] NET: Registered protocol family 24

[ 8.608000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 8.632000] rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller

[ 8.640000] rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1

[ 8.672000] rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000

[ 8.688000] rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00

[ 8.692000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

[ 8.700000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

[ 8.708000] usb usb1: Product: Ralink EHCI Host Controller

[ 8.712000] usb usb1: Manufacturer: Linux 3.3.8 ehci_hcd

[ 8.716000] usb usb1: SerialNumber: rt3xxx

[ 8.724000] hub 1-0:1.0: USB hub found

[ 8.728000] hub 1-0:1.0: 1 port detected

[ 8.988000] sata_sis: Unknown symbol sis_info133_for_sata (err 0)

[ 9.008000] nf_conntrack version 0.5.0 (967 buckets, 3868 max)

[ 9.932000] xt_time: kernel timezone is -0000

[ 10.692000] rt2860v2_ap: module license 'Proprietary' taints kernel.

[ 10.700000] Disabling lock debugging due to kernel taint

[ 10.732000] PanddoraBox AP Driver version-2.7.1.6(Sep 25 2014 14:15:18).

[ 10.840000] Error: Driver 'gpio-keys-polled' is already registered, aborting...

[ 10.856000] mmc_spi: Unknown symbol mmc_spi_get_pdata (err 0)

[ 10.864000] mmc_spi: Unknown symbol mmc_spi_put_pdata (err 0)

[ 14.860000] raeth: HW VLAN TX offload enabled

[ 14.860000] raeth: HW IP/TCP/UDP checksum offload enabled

[ 14.860000] raeth: HW Scatter/Gather TX offload enabled

[ 14.860000] raeth: HW TCP segmentation offload (TSO) enabled

[ 14.908000] device eth2.1 entered promiscuous mode

[ 14.912000] device eth2 entered promiscuous mode

[ 14.920000] br-lan: port 1(eth2.1) entered forwarding state

[ 14.924000] br-lan: port 1(eth2.1) entered forwarding state

[ 16.788000] Started WatchDog Timer.

[ 16.792000] Started WatchDog Timer.

[ 16.928000] br-lan: port 1(eth2.1) entered forwarding state

[ 19.352000] EEPROM:Read from [Factory] offset 0x0,length 0x200.

[ 22.284000] 0x1300 = 00064380

[ 23.200000] device ra0 entered promiscuous mode

[ 23.204000] br-lan: port 2(ra0) entered forwarding state

[ 23.212000] br-lan: port 2(ra0) entered forwarding state

[ 25.216000] br-lan: port 2(ra0) entered forwarding state

[ 29.312000] str_var www.wifi-union.cn?rmac=00:01:42:91:19:94.

[ 29.316000] netlink create success ,webauth moudle started

[ 29.324000] size = 0

BusyBox v1.19.4 (2014-09-25 14:20:05 CST) built-in shell (ash)

Enter 'help' for a list of built-in commands.

______________________________________________________________

| _ _ _ _ _ _ |

| | |_ ___ (_)\\ //__ ___ _ ___ | |_ ___ ___| |__ |

| | __/ _ \ _ \\// _ \/ _ \ \\// | __/ _ \/ __| '_ \ |

| | ||||_| \ | | || __/||_| \ || | || __/ (__| | | |_ |

| \__\___/\\|_| ||\___|\___/\\|| \__\___|\___|_| |_(_) |

| |

| MICHAEL (Michael.xu@taiyear.com) |

|_____________________________________________________________ |

Base on OpenWrt (12.09.2, R1)

root@Taiyear:/#

root@Taiyear:/# uname -r

3.3.8

root@Taiyear:/# date

Thu Sep 25 14:38:40 CST 2014

root@Taiyear:/#

root@Taiyear:/# ls

bin dev etc_ro mnt proc root sys usr www

config etc lib overlay rom sbin tmp var

root@Taiyear:/#

U-Boot 1.1.3 (Dec 27 2013 - 09:14:28)

SoC:MediaTek MT7620

DRAM: Memory Testing..65536K OK. is 64 MB

relocate_code Pointer at: 83fac000

enable ephy clock...done. rf reg 29 = 5

SSC disabled.

spi_wait_nsec: 14

spi device id: ef 40 18 0 0 (40180000)

Flash: W25Q128BV

*** Warning - bad CRC, using default environment

_______________________________________________________________

| ____ _ ____ |

| | _ \ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ |

| | |_) / _` | '_ \ / _` |/ _ \| '__/ _` | _ \ / _ \ \/ / |

| | __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < |

| |_| \__,_|_| |_|\__,_|\___/|_| \__,_|____/ \___/_/\_\ |

| |

| Ralink/MTK SDK Plantform |

| Board:ZBT WR8305RT |

| |

| lintel<lintel.huang@gmail.com> |

|______________________________________________________________|

===============System Info==================

ASIC 7620_MP (Port5<->None)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Flash component: SPI Flash

CPU Speed: 580 MHZ

RAM Size:64 Mbytes

Build Date:Dec 27 2013 Time:09:14:28

============================================

GPIO Init:

UARTF_SHARE_MODE:GPIO

I2C_GPIO_MODE:GPIO

GPIO_MODE_REG:0x1a311d

ReadyLED Bit:0x1

Please choose the operation:

1: Load system code to SDRAM via TFTP.

2: Load system code then write to Flash via TFTP.

3: Boot system code via Flash (default).

4: Entr boot command line interface.

7: Load Boot Loader code then write to Flash via Serial.

9: Load Boot Loader code then write to Flash via TFTP.

3: System Boot system code via Flash.

Press Reset button enter upgrade mode!

## Booting image at bc050000 ...

Image Name: MIPS OpenWrt Linux-3.10.49

Image Type: MIPS Linux Kernel Image (lzma compressed)

Data Size: 1035008 Bytes = 1010.8 kB

Load Address: 80000000

Entry Point: 80000000

Verifying Checksum ... OK

Uncompressing Kernel Image ... OK

No initrd

## Transferring control to Linux (at address 80000000) ...

## Giving linux memsize in MB, 64

Starting kernel ...

[ 0.000000] Linux version 3.10.49 (haijie@xxx.dev.xxxxx) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44550) ) #1 Wed Mar 25 23:09:48 CST 2015

[ 0.000000] Board has DDR2

[ 0.000000] Analog PMU set to hw control

[ 0.000000] Digital PMU set to hw control

[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6

[ 0.000000] bootconsole [early0] enabled

[ 0.000000] CPU revision is: 00019650 (MIPS 24KEc)

[ 0.000000] MIPS: machine is Zbtlink ZBT-WA05

[ 0.000000] Determined physical RAM map:

[ 0.000000] memory: 04000000 @ 00000000 (usable)

[ 0.000000] Initrd not found or empty - disabling initrd

[ 0.000000] Zone ranges:

[ 0.000000] Normal [mem 0x00000000-0x03ffffff]

[ 0.000000] Movable zone start for each node

[ 0.000000] Early memory node ranges

[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]

[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.

[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256

[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2

[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)

[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] Writing ErrCtl register=000190af

[ 0.000000] Readback ErrCtl register=000190af

[ 0.000000] Memory: 61648k/65536k available (2300k kernel code, 3888k reserved, 556k data, 212k init, 0k highmem)

[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] NR_IRQS:256

[ 0.000000] CPU Clock: 580MHz

[ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)

[ 0.060000] pid_max: default: 32768 minimum: 301

[ 0.060000] Mount-cache hash table entries: 512

[ 0.070000] pinctrl core: initialized pinctrl subsystem

[ 0.070000] NET: Registered protocol family 16

[ 0.100000] bio: create slab <bio-0> at 0

[ 0.100000] rt2880_gpio 10000600.gpio: registering 24 gpios

[ 0.110000] rt2880_gpio 10000600.gpio: registering 24 irq handlers

[ 0.110000] rt2880_gpio 10000638.gpio: registering 16 gpios

[ 0.120000] rt2880_gpio 10000638.gpio: registering 16 irq handlers

[ 0.120000] rt2880_gpio 10000660.gpio: registering 32 gpios

[ 0.130000] rt2880_gpio 10000660.gpio: registering 32 irq handlers

[ 0.130000] rt2880_gpio 10000688.gpio: registering 1 gpios

[ 0.140000] rt2880_gpio 10000688.gpio: registering 1 irq handlers

[ 0.140000] Switching to clocksource MIPS

[ 0.150000] NET: Registered protocol family 2

[ 0.150000] TCP established hash table entries: 512 (order: 0, 4096 bytes)

[ 0.160000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)

[ 0.170000] TCP: Hash tables configured (established 512 bind 512)

[ 0.170000] TCP: reno registered

[ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[ 0.190000] NET: Registered protocol family 1

[ 0.190000] rt-timer 10000100.timer: maximum frequncy is 2441Hz

[ 0.220000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[ 0.230000] msgmni has been set to 120

[ 0.240000] io scheduler noop registered

[ 0.240000] io scheduler deadline registered (default)

[ 0.250000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

[ 0.250000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A

[ 0.260000] console [ttyS0] enabled, bootconsole disabled

[ 0.280000] m25p80 spi32766.0: found w25q128, expected w25q64

[ 0.280000] m25p80 spi32766.0: w25q128 (16384 Kbytes)

[ 0.290000] 4 ofpart partitions found on MTD device spi32766.0

[ 0.290000] Creating 4 MTD partitions on "spi32766.0":

[ 0.300000] 0x000000000000-0x000000030000 : "u-boot"

[ 0.310000] 0x000000030000-0x000000040000 : "u-boot-env"

[ 0.310000] 0x000000040000-0x000000050000 : "factory"

[ 0.320000] 0x000000050000-0x0000007b0000 : "firmware"

[ 0.330000] 0x00000014cb40-0x0000007b0000 : "rootfs"

[ 0.330000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only

[ 0.350000] mtd: device 4 (rootfs) set to be root filesystem

[ 0.350000] mtd: partition "rootfs_data" created automatically, ofs=0x5f0000, len=0x1c0000

[ 0.360000] 0x0000005f0000-0x0000007b0000 : "rootfs_data"

[ 0.370000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver

[ 0.380000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5

[ 0.390000] rt3xxx-usbphy usbphy.3: loaded

[ 0.390000] rt2880_wdt 10000120.watchdog: Initialized

[ 0.400000] TCP: cubic registered

[ 0.400000] NET: Registered protocol family 17

[ 0.410000] 8021q: 802.1Q VLAN Support v1.8

[ 0.420000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.

[ 0.430000] Freeing unused kernel memory: 212K (802cb000 - 80300000)

procd: Console is alive

procd: - watchdog -

[ 4.370000] usbcore: registered new interface driver usbfs

[ 4.380000] usbcore: registered new interface driver hub

[ 4.380000] usbcore: registered new device driver usb

[ 4.400000] SCSI subsystem initialized

[ 4.410000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 4.420000] ehci-platform: EHCI generic platform driver

[ 4.620000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled

[ 4.630000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz

[ 4.640000] ehci-platform 101c0000.ehci: EHCI Host Controller

[ 4.640000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1

[ 4.650000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000

[ 4.680000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00

[ 4.680000] hub 1-0:1.0: USB hub found

[ 4.690000] hub 1-0:1.0: 1 port detected

[ 4.690000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[ 4.700000] ohci-platform 101c1000.ohci: Generic Platform OHCI Controller

[ 4.710000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2

[ 4.710000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000

[ 4.780000] hub 2-0:1.0: USB hub found

[ 4.780000] hub 2-0:1.0: 1 port detected

[ 4.790000] leds-gpio gpio-leds.4: pins are not configured from the driver

[ 4.800000] usbcore: registered new interface driver usb-storage

procd: - preinit -

[ 5.450000] 8021q: adding VLAN 0 to HW filter on device eth0

Press the [f] key and hit [enter] to enter failsafe mode

Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level

[ 9.510000] jffs2: notice: (294) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum (0 unchecked, 20 orphan) and 59 of xref (0 dead, 40 orphan) found.

[ 9.530000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab

[ 9.530000] block: unable to load configuration (fstab: Entry not found)

[ 9.540000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab

[ 9.560000] block: extroot: not configured

jffs2 is ready

No jffs2 marker was found

[ 9.690000] jffs2: notice: (291) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum (0 unchecked, 20 orphan) and 59 of xref (0 dead, 40 orphan) found.

[ 10.270000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab

[ 10.280000] block: unable to load configuration (fstab: Entry not found)

[ 10.280000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab

[ 10.300000] block: extroot: not configured

switching to overlay

procd: - early -

procd: - watchdog -

procd: - ubus -

procd: - init -

Please press Enter to activate this console.

[ 12.410000] NET: Registered protocol family 10

[ 12.420000] l2tp_core: L2TP core driver, V2.0

[ 12.420000] l2tp_netlink: L2TP netlink interface

[ 12.440000] gre: GRE over IPv4 demultiplexor driver

[ 12.450000] ip_gre: GRE over IPv4 tunneling driver

[ 12.470000] u32 classifier

[ 12.470000] input device check on

[ 12.480000] Actions configured

[ 12.490000] Mirror/redirect action on

[ 12.510000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)

[ 12.530000] Failed to load ipt action

[ 12.580000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea

[ 12.580000] Backport generated by backports.git backports-20140320-37-g5c33da0

[ 12.670000] usbcore: registered new interface driver ums-alauda

[ 12.690000] usbcore: registered new interface driver ums-cypress

[ 12.710000] usbcore: registered new interface driver ums-datafab

[ 12.710000] usbcore: registered new interface driver ums-freecom

[ 12.730000] usbcore: registered new interface driver ums-isd200

[ 12.730000] usbcore: registered new interface driver ums-jumpshot

[ 12.760000] usbcore: registered new interface driver ums-karma

[ 12.780000] usbcore: registered new interface driver ums-sddr09

[ 12.800000] usbcore: registered new interface driver ums-sddr55

[ 12.800000] usbcore: registered new interface driver ums-usbat

[ 12.830000] usbcore: registered new interface driver usblp

[ 12.880000] xt_time: kernel timezone is -0000

[ 12.910000] cfg80211: Calling CRDA to update world regulatory domain

[ 12.930000] cfg80211: World regulatory domain updated:

[ 12.930000] cfg80211: DFS Master region: unset

[ 12.940000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)

[ 12.940000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)

[ 12.950000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)

[ 12.960000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)

[ 12.970000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)

[ 12.980000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)

[ 12.990000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)

[ 12.990000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)

[ 13.000000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)

[ 13.060000] PPP generic driver version 2.4.2

[ 13.070000] PPP MPPE Compression module registered

[ 13.070000] NET: Registered protocol family 24

[ 13.080000] PPTP driver version 0.8.5

[ 13.100000] l2tp_ppp: PPPoL2TP kernel driver, V2.0

[ 13.120000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected

[ 13.130000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected

[ 19.390000] 8021q: adding VLAN 0 to HW filter on device eth0

[ 19.400000] device eth0.1 entered promiscuous mode

[ 19.400000] device eth0 entered promiscuous mode

[ 19.420000] br-lan: port 1(eth0.1) entered forwarding state

[ 21.420000] br-lan: port 1(eth0.1) entered forwarding state

BusyBox v1.22.1 (2015-03-25 23:06:14 CST) built-in shell (ash)

Enter 'help' for a list of built-in commands.

_______ ________ __

| |.-----.-----.-----.| | | |.----.| |_

| - || _ | -__| || | | || _|| _|

|_______|| __|_____|__|__||________||__| |____|

|__| W I R E L E S S F R E E D O M

-----------------------------------------------------

BARRIER BREAKER (Barrier Breaker, r44874)

-----------------------------------------------------

* 1/2 oz Galliano Pour all ingredients into

* 4 oz cold Coffee an irish coffee mug filled

* 1 1/2 oz Dark Rum with crushed ice. Stir.

* 2 tsp. Creme de Cacao

-----------------------------------------------------

root@OpenWrt:/# procd: - init complete -

root@OpenWrt:/#

root@OpenWrt:/# ifconfig

br-lan Link encap:Ethernet HWaddr 78:A3:51:02:55:CE

inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0

inet6 addr: fe80::7aa3:51ff:fe02:55ce/64 Scope:Link

inet6 addr: fd85:6771:bda1::1/60 Scope:Global

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:51 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:0 (0.0 B) TX bytes:6520 (6.3 KiB)

eth0 Link encap:Ethernet HWaddr 78:A3:51:02:55:CE

inet6 addr: fe80::7aa3:51ff:fe02:55ce/64 Scope:Link

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:70 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000

RX bytes:0 (0.0 B) TX bytes:11813 (11.5 KiB)

Interrupt:5

eth0.1 Link encap:Ethernet HWaddr 78:A3:51:02:55:CE

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:52 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:0 (0.0 B) TX bytes:6566 (6.4 KiB)

eth0.2 Link encap:Ethernet HWaddr 78:A3:51:02:55:CF

inet6 addr: fe80::7aa3:51ff:fe02:55cf/64 Scope:Link

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:13 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:0 (0.0 B) TX bytes:3486 (3.4 KiB)

lo Link encap:Local Loopback

inet addr:127.0.0.1 Mask:255.0.0.0

inet6 addr: ::1/128 Scope:Host

UP LOOPBACK RUNNING MTU:65536 Metric:1

RX packets:194 errors:0 dropped:0 overruns:0 frame:0

TX packets:194 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:13152 (12.8 KiB) TX bytes:13152 (12.8 KiB)

秒客网

原始启动log&新log

相关文章