FPGA图像仿真平台
1 引言
在使用modelsim进行图像算法的功能仿真时，无法得到图像的实时预览，因此直观性有所欠缺。因此可配合matlab使用，通过modelsim读出txt格式的图像，利用matlab进行转换与显示，从而既可验证时序关系，又可直观看到算法的效果。
2 matlab代码
2.1 图片读取及通道转换
注意事项：图片与程序需放到同一文件夹内
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% ProjectName : ycbcrcode.m
% Author : Huhao
% Description : image to txt
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
clear all
close all
clc
img = imread('card.jpg');
ycbcr = rgb2ycbcr(img);
y=ycbcr(:,:,1);
cb=ycbcr(:,:,2);
cr=ycbcr(:,:,3);
2.2 图片转化为txt格式
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% ProjectName : rgb2txt.m
% Author : Huhao
% Description : rgb to text
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
clear all
close all
clc
img = imread('card.jpg');
r=img(:,:,1);
g=img(:,:,2);
b=img(:,:,3);
figure,
subplot(221),imshow(r),title('R');
subplot(222),imshow(g),title('G');
subplot(223),imshow(b),title('B');
subplot(224),imshow(img),title('RGB img');
r1=r';
g1=g';
b1=b';
fid1=fopen('img_r.txt','wt');
% fprintf(fid1,'%x\n',r1);%hexadecimal
fprintf(fid1,'%g\n',r1);%Binary
fclose(fid1);
fid2=fopen('img_g.txt','wt');
% fprintf(fid2,'%x\n',g1);
fprintf(fid2,'%g\n',g1);
fclose(fid2);
fid3=fopen('img_b.txt','wt');
% fprintf(fid3,'%x\n',b1);
fprintf(fid3,'%g\n',b1);
fclose(fid3);
2.3 modelsim输出的txt文档重新转化为图片并显示
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% ProjectName : txt2rgb.m
% Author : Huhao
% Description : text to rgb
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
clear all
close all
clc
r_load = load('img_r.txt');
g_load = load('img_g.txt');
b_load = load('img_b.txt');
length = 760;%image length
width = 397;%image width
r2 = reshape(r_load,[length, width]);
r2 = uint8(r2');
g2 = reshape(g_load,[length, width]);
g2 = uint8(g2');
b2 = reshape(b_load,[length, width]);
b2 = uint8(b2');
rgb_img(:,:,1)=r2;
rgb_img(:,:,2)=g2;
rgb_img(:,:,3)=b2;
figure,
subplot(221),imshow(r2),title('R');
subplot(222),imshow(g2),title('G');
subplot(223),imshow(b2),title('B');
subplot(224),imshow(rgb_img),title('RGB img');
3 结果显示
3.1 图片转化为txt结果
图1 rgb to txt三通道图片
图2 rgb to txt得到的三通道txt数据
3.2 txt重新转化为图片结果
图3 txt to rgb三通道图片