Linux双网卡绑定

时间：2021-05-07 15:29:30

Linux双网卡绑定

作者：Eric

微信：loveoracle11g

eth0和eth1绑定为bond0

[root@rac-node1 ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0

TYPE=Ethernet

BOOTPROTO=none

ONBOOT=yes

USERCTL=no

DEVICE=eth0

MASTER=bond0

SLAVE=yes

[root@rac-node1 ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1

TYPE=Ethernet

BOOTPROTO=none

ONBOOT=yes

USERCTL=no

DEVICE=eth1

MASTER=bond0

SLAVE=yes

[root@rac-node1 ~]# cat /etc/sysconfig/network-scripts/ifcfg-bond0

TYPE=Ethernet

BOOTPROTO=none

ONBOOT=yes

USERCTL=no

DEVICE=bond0

IPADDR=192.168.56.11

NETMASK=255.255.255.0

GATEWAY=192.168.56.2

NM_CONTROLLED=no

使用Vim文本编辑器创建一个用于网卡绑定的驱动文件，使得绑定后的bond0网卡设备能够支持绑定技术（bonding）；同时定义网卡以mode6模式进行绑定，且出现故障时自动切换的时间为100毫秒。

常见的网卡绑定驱动有三种模式—mode0、mode1和mode6。下面以绑定两块网卡为例，讲解使用的情景。

mode0（平衡负载模式）：平时两块网卡均工作，且自动备援，但需要在与服务器本地网卡相连的交换机设备上进行端口聚合来支持绑定技术。

mode1（自动备援模式）：平时只有一块网卡工作，在它故障后自动替换为另外的网卡。

mode6（平衡负载模式）：平时两块网卡均工作，且自动备援，无须交换机设备提供辅助支持。

[root@rac-node1 ~]# cat /etc/modprobe.d/bond.conf

alias bond0 bonding

options bond0 miimon=100 mode=6

[root@rac-node1 ~]# /etc/init.d/network restart

Shutting down interface eth0:  /etc/sysconfig/network-scripts/ifdown-eth: line 124: /sys/class/net/bond0/bonding/slaves: No such file or directory

                                                           [  OK  ]

Shutting down loopback interface:                          [  OK  ]

Bringing up loopback interface:                            [  OK  ]

Bringing up interface bond0:  Determining if ip address 192.168.10.11 is already in use for device bond0...

                                                           [  OK  ]

[root@rac-node1 ~]# ifconfig

bond0     Link encap:Ethernet  HWaddr 00:0C:29:FD:2F:24

          inet 192.168.56.11  netmask 255.255.255.0  broadcast 192.168.56.255

          inet6 addr: fe80::20c:29ff:fefd:2f24/64 Scope:Link

          UP BROADCAST RUNNING MASTER MULTICAST  MTU:1500  Metric:1

          RX packets:20 errors:0 dropped:0 overruns:0 frame:0

          TX packets:24 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0

          RX bytes:1522 (1.4 KiB)  TX bytes:2746 (2.6 KiB)

eth0      Link encap:Ethernet  HWaddr 00:0C:29:FD:2F:24

          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1

          RX packets:2420 errors:0 dropped:0 overruns:0 frame:0

          TX packets:2034 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000

          RX bytes:227710 (222.3 KiB)  TX bytes:298140 (291.1 KiB)

eth1      Link encap:Ethernet  HWaddr 00:0C:29:FD:2F:2E

          UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1

          RX packets:6 errors:0 dropped:0 overruns:0 frame:0

          TX packets:3 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000

          RX bytes:360 (360.0 b)  TX bytes:592 (592.0 b)

lo        Link encap:Local Loopback

          inet addr:127.0.0.1  Mask:255.0.0.0

          inet6 addr: ::1/128 Scope:Host

          UP LOOPBACK RUNNING  MTU:65536  Metric:1

          RX packets:118 errors:0 dropped:0 overruns:0 frame:0

          TX packets:118 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:0

          RX bytes:10116 (9.8 KiB)  TX bytes:10116 (9.8 KiB)

[root@rac-node1 ~]# /etc/init.d/network restart

Shutting down interface bond0:                             [  OK  ]

Shutting down loopback interface:                          [  OK  ]

Bringing up loopback interface:                            [  OK  ]

Bringing up interface bond0:  Determining if ip address 192.168.56.11 is already in use for device bond0...

                                                           [  OK  ]

相关文章