- ???? 博主主页： 【Systemcall小酒屋】
- ???? 博主追寻：热衷于用简单的案例讲述复杂的技术，“假传万卷书，真传一案例”，这是林群院士说过的一句话，另外“成就是最好的老师”，技术既要沉淀，也得分享，成就感的正反馈是支持我持续耕耘的动力！
![[ROC-RK3568-PC] [Firefly-Android] 10min带你了解Camera的使用](https://image.shishitao.com:8440/aHR0cHM6Ly9zMi41MWN0by5jb20vaW1hZ2VzL2Jsb2cvMjAyMzAzLzI1MDAxODMxXzY0MWRjZDU3YWI4MGE3ODcyNC5qcGc%3D.jpg?w=700&webp=1 "[ROC-RK3568-PC] [Firefly-Android] 10min带你了解Camera的使用")
文章目录
- 一、MIPI CSI
- 1.1 Full Mode特点
- 1.2 Split Mode特点
- 二、Full Mode配置
- 2.1 配置sensor端
- 2.2 csi2_dphy0相关配置
- 2.3 isp相关配置
- 三、Split Mode配置
- 3.1 配置sensor端
- 3.2 csi2_dphy1/csi2_dphy2相关配置
- 3.3 isp相关配置
- 四、软件相关目录
- 五、单目CAM-8MS1M/双目CAM-2MS2MF摄像头的使用
- 5.1 使用单目摄像头CAM-8MS1M
- 5.2 使用双目摄像头CAM-2MS2MF
- 六、Camera底层调试
- 七、Android系统使用camera应用
- 八、IQ文件
一、MIPI CSI
RK3566/RK3568平台仅有一个标准物理mipi csi2 dphy，可以工作在两个模式：full mode 和split mode，拆分为csi2_dphy0/csi2_dphy1/csi2_dphy2三个逻辑dphy
1.1 Full Mode特点
- 仅使用csi2_dphy0。csi2_dphy0与csi2_dphy1/csi2_dphy2互斥，不可同时使用
- data lane最大4 lanes
- 最大速率2.5Gbps/lane
1.2 Split Mode特点
- 仅使用csi2_dphy1和csi2_dphy2，两者与 csi2_dphy0 互斥，不可同时使用
- csi2_dphy1和csi2_dphy2可同时使用
- csi2_dphy1和csi2_dphy2各自的data lane最大是2 lanes
- csi2_dphy1对应物理dphy的lane0/lane1
- csi2_dphy2对应物理dphy的lane2/lane3
- 最大速率2.5Gbps/lane
![[ROC-RK3568-PC] [Firefly-Android] 10min带你了解Camera的使用](https://image.shishitao.com:8440/aHR0cHM6Ly9zMi41MWN0by5jb20vaW1hZ2VzL2Jsb2cvMjAyMzAzLzI1MDAxODMxXzY0MWRjZDU3ZGM2NTI1MTQ1Ni5wbmc%3D.png?w=700&webp=1 "[ROC-RK3568-PC] [Firefly-Android] 10min带你了解Camera的使用")
一般来说，如果用单目摄像头可以配置full mode，若使用双目摄像头可以配置split mode
二、Full Mode配置
链接关系: sensor->csi2_dphy0->isp
2.1 配置sensor端
需要根据板子原理图的MIPI CSI接口找到sensor是挂在哪个I2C总线上，然后在对应的I2C节点配置camera节点，正确配置camera模组的I2C设备地址、引脚等属性。
如下ROC-RK3568-PC的xc7160配置：
&i2c4 {
status = "okay";
XC7160: XC7160b@1b {
status = "okay";
compatible = "firefly,xc7160";
reg = <0x1b>;
clocks = <&cru CLK_CIF_OUT>;
clock-names = "xvclk";
power-domains = <&power RK3568_PD_VI>;
pinctrl-names = "default";
pinctrl-0 = <&cif_clk>;
power-gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_LOW>;
reset-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
pwdn-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
firefly,clkout-enabled-index = <0>;
rockchip,camera-module-index = <0>;
rockchip,camera-module-facing = "back";
rockchip,camera-module-name = "NC";
rockchip,camera-module-lens-name = "NC";
port {
xc7160_out: endpoint {
remote-endpoint = <&mipi_in_ucam4>;
data-lanes = <1 2 3 4>;
};
};
};
};2.2 csi2_dphy0相关配置
csi2_dphy0与csi2_dphy1/csi2_dphy2互斥,不可同时使用。另外需要使能csi2_dphy_hw节点：
&csi2_dphy0 {
status = "okay";
/*
* dphy0 only used for full mode,
* full mode and split mode are mutually exclusive
*/
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
...
mipi_in_ucam4: endpoint@5 {
reg = <5>;
remote-endpoint = <&xc7160_out>;
data-lanes = <1 2 3 4>;
};
};
port@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
csidphy_out: endpoint@0 {
reg = <0>;
remote-endpoint = <&isp0_in>;
};
};
};
};
&csi2_dphy_hw {
status = "okay";
};
&csi2_dphy1 {
status = "disabled";
};
&csi2_dphy2 {
status = "disabled";
};2.3 isp相关配置
其中rkisp_vir0节点的remote-endpoint指向csidphy_out：
&rkisp {
status = "okay";
};
&rkisp_mmu {
status = "okay";
};
&rkisp_vir0 {
status = "okay";
port {
#address-cells = <1>;
#size-cells = <0>;
isp0_in: endpoint@0 {
reg = <0>;
remote-endpoint = <&csidphy_out>;
};
};
};三、Split Mode配置
链接关系:
sensor1->csi_dphy1->isp_vir0sensor2->csi_dphy2->mipi_csi2->vicap->isp_vir1
3.1 配置sensor端
根据板子原理图的MIPI CSI接口找到两个sensor是挂在哪个I2C总线上，然后在对应的I2C节点配置两个camera节点，正确配置camera模组的I2C设备地址、引脚等属性。如下ROC-RK3568-PC的gc2053/gc2093配置：
&i2c4 {
status = "okay";
gc2053: gc2053@37 { //IR
status = "okay";
compatible = "galaxycore,gc2053";
reg = <0x37>;
avdd-supply = <&vcc_camera>;
power-domains = <&power RK3568_PD_VI>;
clock-names = "xvclk";
pinctrl-names = "default";
clocks = <&pmucru CLK_WIFI>;
pinctrl-0 = <&refclk_pins>;
power-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;//IR_PWR_EN
pwdn-gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_LOW>;
firefly,clkout-enabled-index = <1>;
rockchip,camera-module-index = <0>;
rockchip,camera-module-facing = "back";
rockchip,camera-module-name = "YT-RV1109-2-V1";
rockchip,camera-module-lens-name = "40IR-2MP-F20";
port {
gc2053_out: endpoint {
remote-endpoint = <&dphy1_in>;
data-lanes = <1 2>;
};
};
};
gc2093: gc2093b@7e { //RGB
status = "okay";
compatible = "galaxycore,gc2093";
reg = <0x7e>;
avdd-supply = <&vcc_camera>;
power-domains = <&power RK3568_PD_VI>;
clock-names = "xvclk";
pinctrl-names = "default";
flash-leds = <&flash_led>;
pwdn-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
firefly,clkout-enabled-index = <0>;
rockchip,camera-module-index = <1>;
rockchip,camera-module-facing = "front";
rockchip,camera-module-name = "YT-RV1109-2-V1";
rockchip,camera-module-lens-name = "40IR-2MP-F20";
port {
gc2093_out: endpoint {
remote-endpoint = <&dphy2_in>;
data-lanes = <1 2>;
};
};
};
};3.2 csi2_dphy1/csi2_dphy2相关配置
csi2_dphy0与csi2_dphy1/csi2_dphy2互斥,不可同时使用：
&csi2_dphy0 {
status = "disabled";
};
&csi2_dphy1 {
status = "okay";
/*
* dphy1 only used for split mode,
* can be used concurrently with dphy2
* full mode and split mode are mutually exclusive
*/
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
dphy1_in: endpoint@1 {
reg = <1>;
remote-endpoint = <&gc2053_out>;
data-lanes = <1 2>;
};
};
port@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
dphy1_out: endpoint@1 {
reg = <1>;
remote-endpoint = <&isp0_in>;
};
};
};
};
&csi2_dphy2 {
status = "okay";
/*
* dphy2 only used for split mode,
* can be used concurrently with dphy1
* full mode and split mode are mutually exclusive
*/
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
dphy2_in: endpoint@1 {
reg = <1>;
remote-endpoint = <&gc2093_out>;
data-lanes = <1 2>;
};
};
port@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
dphy2_out: endpoint@1 {
reg = <1>;
remote-endpoint = <&mipi_csi2_input>;
};
};
};
};
&csi2_dphy_hw {
status = "okay";
};
&mipi_csi2 {
status = "okay";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
mipi_csi2_input: endpoint@1 {
reg = <1>;
remote-endpoint = <&dphy2_out>;
data-lanes = <1 2>;
};
};
port@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
mipi_csi2_output: endpoint@0 {
reg = <0>;
remote-endpoint = <&cif_mipi_in>;
data-lanes = <1 2>;
};
};
};
};
&rkcif_mipi_lvds {
status = "okay";
port {
cif_mipi_in: endpoint {
remote-endpoint = <&mipi_csi2_output>;
data-lanes = <1 2>;
};
};
};
&rkcif_mipi_lvds_sditf {
status = "okay";
port {
mipi_lvds_sditf: endpoint {
remote-endpoint = <&isp1_in>;
data-lanes = <1 2>;
};
};
};3.3 isp相关配置
其中rkisp_vir0节点的remote-endpoint指向dphy1_out
&rkisp {
status = "okay";
};
&rkisp_mmu {
status = "okay";
};
&rkisp_vir0 {
status = "okay";
port {
#address-cells = <1>;
#size-cells = <0>;
isp0_in: endpoint@0 {
reg = <0>;
remote-endpoint = <&dphy1_out>;
};
};
};
&rkisp_vir1 {
status = "okay";
port {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
isp1_in: endpoint@0 {
reg = <0>;
remote-endpoint = <&mipi_lvds_sditf>;
};
};
};
&rkcif_mmu {
status = "okay";
};
&rkcif {
status = "okay";
};四、软件相关目录
Linux Kernel-4.19
|-- arch/arm/boot/dts #DTS配置文件
|-- drivers/phy/rockchip
|-- phy-rockchip-mipi-rx.c #mipi dphy驱动
|-- phy-rockchip-csi2-dphy-common.h
|-- phy-rockchip-csi2-dphy-hw.c
|-- phy-rockchip-csi2-dphy.c
|-- drivers/media
|-- platform/rockchip/cif #RKCIF驱动
|-- platform/rockchip/isp #RKISP驱动
|-- dev #包含 probe、异步注册、clock、pipeline、 iommu及media/v4l2 framework
|-- capture #包含 mp/sp/rawwr的配置及 vb2,帧中断处理
|-- dmarx #包含 rawrd的配置及 vb2,帧中断处理
|-- isp_params #3A相关参数设置
|-- isp_stats #3A相关统计
|-- isp_mipi_luma #mipi数据亮度统计
|-- regs #寄存器相关的读写操作
|-- rkisp #isp subdev和entity注册
|-- csi #csi subdev和mipi配置
|-- bridge #bridge subdev,isp和ispp交互桥梁
|-- platform/rockchip/ispp #rkispp驱动
|-- dev #包含 probe、异步注册、clock、pipeline、 iommu及media/v4l2 framework
|-- stream #包含 4路video输出的配置及 vb2,帧中断处理
|-- rkispp #ispp subdev和entity注册
|-- params #TNR/NR/SHP/FEC/ORB参数设置
|-- stats #ORB统计信息五、单目CAM-8MS1M/双目CAM-2MS2MF摄像头的使用
ROC-RK3568-PC已经配置好相应的dts，单目摄像头CAM-8MS1M和双目摄像头CAM-2MS2MF使用互斥，只需包含相应的dtsi文件即可使用单目摄像头CAM-8MS1M或双目摄像头CAM-2MS2MF
5.1 使用单目摄像头CAM-8MS1M
dts的配置默认使用单目摄像头：
diff --git a/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dts b/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dts
index 7e2a8b2..14fa027 100755
--- a/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dts
+++ b/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dts
@@ -7,6 +7,15 @@
+#include "rk3568-firefly-roc-pc-cam-8ms1m.dtsi"
+//#include "rk3568-firefly-roc-pc-cam-2ms2m.dtsi"5.2 使用双目摄像头CAM-2MS2MF
diff --git a/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dts b/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dts
index 7e2a8b2..14fa027 100755
--- a/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dts
+++ b/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dts
@@ -7,6 +7,15 @@
- #include "rk3568-firefly-roc-pc-cam-8ms1m.dtsi"
+//#include "rk3568-firefly-roc-pc-cam-8ms1m.dtsi"
- //#include "rk3568-firefly-roc-pc-cam-2ms2m.dtsi"
+ #include "rk3568-firefly-roc-pc-cam-2ms2m.dtsi"六、Camera底层调试
使用v4l2-ctl抓取camera数据帧：
v4l2-ctl --verbose -d /dev/video0 --set-fmt-video=width=1920,height=1080,pixelformat='NV12' --stream-mmap=4 --set-selection=target=crop,flags=0,top=0,left=0,width=1920,height=1080 --stream-to=/data/out.yuv把out.yuv文件拷贝出来通过ubuntu去查看：
ffplay -f rawvideo -video_size 1920x1080 -pix_fmt nv12 out.yuv七、Android系统使用camera应用
Android系统使用camera的apk打开摄像头需要配置camera3_profiles*.xml，具体可参考Android SDK hardware/rockchip/camera/etc/camera目录下的文件
八、IQ文件
raw摄像头支持的iq文件路径external/camera_engine_rkaiq/iqfiles/isp21, 与以前不一样的地方是iq文件不再采用.xml的方式，而是采用.json的方式。虽有提供xml转json的工具, 但isp20的xml配置转换后也不适用isp21。
若使用raw摄像头sensor，请留意isp21目录所支持的iq文件。