文章目录
- 一、首先是界面介绍。
- 二、工具的目的
- 三、ls_gpio.h模板
- 四、ls_syscfg.h 模板
- 五、简单讲解功能
一、首先是界面介绍。
![[LsSDK][tool] ls_syscfg_gui 简介](https://image.shishitao.com:8440/aHR0cHM6Ly9zMi41MWN0by5jb20vaW1hZ2VzL2Jsb2cvMjAyMzAzLzI1MDAxMzM0XzY0MWRjYzJlYThjMTQ1Nzc2MS5naWY%3D.gif?w=700 "[LsSDK][tool] ls_syscfg_gui 简介")
![[LsSDK][tool] ls_syscfg_gui 简介](https://image.shishitao.com:8440/aHR0cHM6Ly9zMi41MWN0by5jb20vaW1hZ2VzL2Jsb2cvMjAyMzAzLzI1MDAxMzM0XzY0MWRjYzJlZDA0NDA0NDIxMi5naWY%3D.gif?w=700 "[LsSDK][tool] ls_syscfg_gui 简介")
二、工具的目的
- 可视化选择IO口功能。
- *配置IO支持的功能。
- 适用各类MCU，方便移植和开发。
- 功能配置和裁剪（选项-syscfg-待完成–需要适配keil语法有些麻烦）
三、ls_gpio.h模板
/********************************************************************************
* @file ls_gpio.h
* @author jianqiang.xue
* @version V1.1.0
* @date 2022-12-11
* @brief 业务类--GPIO定义
********************************************************************************/
#ifndef __LS_GPIO_H
#define __LS_GPIO_H
#define LS_IO_VERSION "CX32L003_通用模板"
#include "cx32l003_hal.h"
#include "cx32l003_hal_def.h"
#include "ls_syscfg.h"
#include "bsp_gpio.h"
#include "bsp_exti.h"
/* GPIO_EXTI_INT_EDGE; // 中断类型 边沿触发
GPIO_EXTI_INT_LOWFALL; // 下降沿触发中断
GPIO_EXTI_INT_HIGHRISE; // 上升沿触发中断
GPIO_EXTI_INT_FALLRISE; // 下降沿上升沿都触发中断
GPIO_EXTI_INT_LEVEL; // 中断类型 电平触发
GPIO_EXTI_INT_LOWFALL; // 低电平触发中断
GPIO_EXTI_INT_HIGHRISE; // 高电平触发中断 */
#define GPIO_CLK(GPIO) (RCC_HCLKEN_##GPIO##CKEN)
#define GPIO_APBx (0)
/************************************GPIO***********************************/
#define LS_IO_NUM (16)
/* Public Struct -------------------------------------------------------------*/
union io_support_t {
uint64_t val; // 对外值
struct {
uint64_t swo : 1;
uint64_t adc0_ch0 : 1;
uint64_t adc0_ch1 : 1;
uint64_t adc0_ch2 : 1;
uint64_t adc0_ch3 : 1;
uint64_t adc0_ch4 : 1;
uint64_t adc0_ch5 : 1;
uint64_t adc0_ch6 : 1;
uint64_t adc1_ch0 : 1;
uint64_t adc1_ch1 : 1;
uint64_t adc1_ch2 : 1;
uint64_t adc1_ch3 : 1;
uint64_t adc1_ch4 : 1;
uint64_t adc1_ch5 : 1;
uint64_t adc1_ch6 : 1;
uint64_t tim1_ch1 : 1; // PWM0
uint64_t tim1_ch2 : 1; // PWM1
uint64_t tim1_ch3 : 1; // PWM2
uint64_t tim1_ch4 : 1; // PWM3
uint64_t tim2_ch1 : 1; // PWM4
uint64_t tim2_ch2 : 1; // PWM5
uint64_t tim2_ch3 : 1; // PWM6
uint64_t tim2_ch4 : 1; // PWM7
uint64_t uart0_tx : 1;
uint64_t uart0_rx : 1;
uint64_t uart1_tx : 1;
uint64_t uart1_rx : 1;
uint64_t uart2_tx : 1;
uint64_t uart2_rx : 1;
uint64_t i2c0_scl : 1; // 硬件IIC
uint64_t i2c0_sda : 1;
uint64_t i2c1_scl : 1;
uint64_t i2c1_sda : 1;
uint64_t i2c_scl_soft : 1; // 软件IIC
uint64_t i2c_sda_soft : 1;
uint64_t spi0_clk : 1;
uint64_t spi0_mosi : 1;
uint64_t spi0_miso : 1;
uint64_t spi0_nss : 1;
uint64_t spi1_clk : 1;
uint64_t spi1_mosi : 1;
uint64_t spi1_miso : 1;
uint64_t spi1_nss : 1;
#if !LS_IO_EXTEND_SUPPORT
uint64_t reserve : 7;
#endif
} bit;
};
typedef enum {
IO_TYPE_IN_NULL = 0, // 默认输入 无上下拉
IO_TYPE_IN_PULLUP, // 输入，上拉
IO_TYPE_IN_PULLDOWN, // 输入，下拉
IO_TYPE_OUT_PP, // 默认输出 推免输出
IO_TYPE_OUT_OD, // 开漏输出
// 中断输入
IO_TYPE_INIRQ_LEVEL_LOW, // 电平触发-低电平
IO_TYPE_INIRQ_LEVEL_HIGH, // 电平触发-高电平
IO_TYPE_INIRQ_EDGE_LOWFALL, // 边沿触发-下降沿
IO_TYPE_INIRQ_EDGE_HIGHRISE, // 边沿触发-上降沿
IO_TYPE_INIRQ_EDGE_FALLRISE, // 边沿触发-任意电平变化
IO_TYPE_SWO, // 默认烧录脚
IO_TYPE_KEY, // 按键，会注册到软定时器中扫描
IO_TYPE_MATRIX_KEY_X, // 矩阵键盘X轴，会注册到软定时器中扫描
IO_TYPE_MATRIX_KEY_Y, // 矩阵键盘Y轴，会注册到软定时器中扫描
IO_TYPE_W2812X,
IO_TYPE_ADC0_CH0,
IO_TYPE_ADC0_CH1,
IO_TYPE_ADC0_CH2,
IO_TYPE_ADC0_CH3,
IO_TYPE_ADC0_CH4,
IO_TYPE_ADC0_CH5,
IO_TYPE_ADC0_CH6,
IO_TYPE_ADC1_CH0,
IO_TYPE_ADC1_CH1,
IO_TYPE_ADC1_CH2,
IO_TYPE_ADC1_CH3,
IO_TYPE_ADC1_CH4,
IO_TYPE_ADC1_CH5,
IO_TYPE_ADC1_CH6,
IO_TYPE_TIM1_CH1, // PWM0
IO_TYPE_TIM1_CH2, // PWM1
IO_TYPE_TIM1_CH3, // PWM2
IO_TYPE_TIM1_CH4, // PWM3
IO_TYPE_TIM2_CH1, // PWM4
IO_TYPE_TIM2_CH2, // PWM5
IO_TYPE_TIM2_CH3, // PWM6
IO_TYPE_TIM2_CH4, // PWM7
IO_TYPE_UART0_TX, // 串口，通过命令配置电气特性
IO_TYPE_UART0_RX,
IO_TYPE_UART1_TX, // 串口，通过命令配置电气特性
IO_TYPE_UART1_RX,
IO_TYPE_UART2_TX,
IO_TYPE_UART2_RX,
IO_TYPE_I2C0_SCL, // 硬件IIC
IO_TYPE_I2C0_SDA, // 硬件IIC
IO_TYPE_I2C1_SCL,
IO_TYPE_I2C1_SDA,
IO_TYPE_I2C_SCL_SOFT, // 软件IIC
IO_TYPE_I2C_SDA_SOFT, // 软件IIC
IO_TYPE_SPI0_CLK,
IO_TYPE_SPI0_MOSI,
IO_TYPE_SPI0_MISO,
IO_TYPE_SPI0_NSS,
IO_TYPE_SPI1_CLK,
IO_TYPE_SPI1_MOSI,
IO_TYPE_SPI1_MISO,
IO_TYPE_SPI1_NSS,
IO_TYPE_MAX,
} io_type_t;
extern const union io_support_t g_io_support[LS_IO_NUM];
extern const io_type_t g_io_default_type[LS_IO_NUM];
extern const bsp_gpio_t g_io_cfg[LS_IO_NUM];
#ifdef LS_IO
const bsp_gpio_t g_io_cfg[LS_IO_NUM] = {
{(GPIOD), (GPIO_PIN_2), GPIO_CLK(GPIOD), (0), (GPIOD_IRQn)},
{(GPIOD), (GPIO_PIN_3), GPIO_CLK(GPIOD), (0), (GPIOD_IRQn)},
{(GPIOD), (GPIO_PIN_4), GPIO_CLK(GPIOD), (0), (GPIOD_IRQn)},
{(GPIOD), (GPIO_PIN_5), GPIO_CLK(GPIOD), (0), (GPIOD_IRQn)},
{(GPIOD), (GPIO_PIN_6), GPIO_CLK(GPIOD), (0), (GPIOD_IRQn)},
{(GPIOC), (GPIO_PIN_3), GPIO_CLK(GPIOC), (0), (GPIOC_IRQn)},
{(GPIOC), (GPIO_PIN_4), GPIO_CLK(GPIOC), (0), (GPIOC_IRQn)},
{(GPIOC), (GPIO_PIN_5), GPIO_CLK(GPIOC), (0), (GPIOC_IRQn)},
{(GPIOC), (GPIO_PIN_6), GPIO_CLK(GPIOC), (0), (GPIOC_IRQn)},
{(GPIOB), (GPIO_PIN_4), GPIO_CLK(GPIOB), (0), (GPIOB_IRQn)},
{(GPIOB), (GPIO_PIN_5), GPIO_CLK(GPIOB), (0), (GPIOB_IRQn)},
{(GPIOA), (GPIO_PIN_3), GPIO_CLK(GPIOA), (0), (GPIOA_IRQn)},
{(GPIOD), (GPIO_PIN_1), GPIO_CLK(GPIOD), (0), (GPIOD_IRQn)},
{(GPIOC), (GPIO_PIN_7), GPIO_CLK(GPIOC), (0), (GPIOC_IRQn)},
{(GPIOA), (GPIO_PIN_1), GPIO_CLK(GPIOA), (0), (GPIOA_IRQn)},
{(GPIOA), (GPIO_PIN_2), GPIO_CLK(GPIOA), (0), (GPIOA_IRQn)},
};
const union io_support_t g_io_support[LS_IO_NUM] = {
{0x808010010}, {0x1100020}, {0x888000}, {0x2022C00040}, {0x1045110080},
{0x42220004}, {0x24440008}, {0x808000000}, {0x1010408002}, {0x4020800000},
{0x841080000}, {0x4010200000}, {0x2000001}, {0x4100001}, {0x45000000},
{0x4022920000},
};
const io_type_t g_io_default_type[LS_IO_NUM] = {
IO_TYPE_TIM1_CH2, IO_TYPE_TIM2_CH2, IO_TYPE_TIM1_CH1, IO_TYPE_TIM2_CH4, IO_TYPE_ADC0_CH6,
IO_TYPE_TIM1_CH3, IO_TYPE_TIM1_CH4, IO_TYPE_TIM2_CH1, IO_TYPE_ADC0_CH0, IO_TYPE_IN_NULL,
IO_TYPE_IN_NULL, IO_TYPE_TIM2_CH3, IO_TYPE_SWO, IO_TYPE_SWO, IO_TYPE_UART0_RX,
IO_TYPE_UART0_TX,
};
#else
#endif
#endif- 定义IO支持类型
- 定义默认类型，上电自动初始化完毕
四、ls_syscfg.h 模板
/********************************************************************************
* @file ls_syscfg.h
* @author jianqiang.xue
* @version V1.1.0
* @date 2023-03-04
* @brief 业务类--功能宏定义
********************************************************************************/
#ifndef __LS_SYSCFG_H
#define __LS_SYSCFG_H
//-------- <<< Use Configuration Wizard in Context Menu >>> -----------------
/**************************************LOG**************************************/
// <e> Log Switch
// =======================
#define LS_LOG_SWITCH (0x1)
// <o> Log Grade
// <i> Default: 0
// <0=> ALL
// <1=> TRACE
// <2=> DEBUG
// <3=> INFO
// <4=> WARN
// <5=> ERROR
// <6=> FATAL
// <7=> OFF
#define LS_LOG_GRADE (0x2)
// <o> Log Out
// <i> Default: 0
// <0=> RTT
// <1=> UART
#define LS_LOG_OUT (0x1)
// <q> MAX LEN
// <i> Default: 128 Min Data Len 128
#define LS_LOG_MAX_LEN (128)
// </e>
/************************************FLASH**************************************/
// <h> FLASH
// =======================
//
// <o> Page Size
// <i> Default: 0x200 (512 byte)
#define LS_FLASH_PAGE_SIZE (0x200U)
// <o> Flash Max Size
// <i> Default: 0x10000 (64K byte)
#define LS_FLASH_MAX_SIZE (0x10000U)
// <o> Boot Loader Starting Address
// <i> Default: 0
#define LS_FLASH_START_ADDR (0x0000000)
// <o> Boot Loader Size
// <i> Default: 0x1400 (5K byte), use dfu 0x2000
#define LS_FLASH_BOOT_SIZE (0x2000)
// <o> Kv Flash Page
// <i> Default: 3
#define LS_FLASH_KV_PAGE (3)
// <o> Flash Write Byte Ability
// <i> The ability to write is also byte to it.
// <i> Default: 4
#define LS_FLASH_WRITE_BYTE_ABILITY (1)
// <o> FLASH_INFO_TYPE(MCU user Kv_Sys / NRF user FDS)
// <0=> KV_SYS
// <1=> FDS
#define LS_FLASH_INFO_TYPE (0)
// </h>
/*************************************APP_IO************************************/
// <h> APP_IO
// =======================
// <q> Save Flash Support
#define LS_APP_IO_SAVE_SUPPORT (0)
// <q> Active Report Support (ATCMD enevt)
#define LS_APP_IO_ACTIVE_REPORT_SUPPORT (0)
// <q> Key Scan Support
#define LS_APP_IO_KEY_SCAN_SUPPORT (1)
// <q> Matrix Key Support
#define LS_APP_IO_MATRIX_KEY_SUPPORT (0)
// <e> Tiemr Support (IO Operation)
#define LS_APP_IO_TIMER_SUPPORT (1)
// <o> Task Number
#define LS_APP_IO_TIMER_NUM (2)
// <o> Timer Time (ms)
#define LS_APP_IO_TIMER_TIME_MS (1000)
// </e>
// <q> Sys Vcc Support
#define LS_APP_IO_SYS_VCC_SUPPORT (0)
// <q> Swo Off
#define LS_APP_IO_SWO_OFF (0)
// <q> Extend Support
#define LS_IO_EXTEND_SUPPORT (0)
// </h>
/**************************************KEY**************************************/
// <h> KEY
// =======================
// <o> Button scan cycle (ms) <10-65535>
// <i> Default: 10
#define LS_BUTTON_SCAN_CYCLE_MS (10)
// <o> Single click time(ms) <0-65535>
// <i> 1 timec of one click
// <i> Default: 100
#define LS_BUTTON_SINGLE_CLICK_TIME (50)
// <o> Release time(ms) <0-65535>
// <i> press -> release
// <i> Default: 100
#define LS_BUTTON_RELEASE_TIME (140)
// <o> Double click time(ms) <0-65535>
// <i> 1 timec of double click interval time
// <i> Default: 150
#define LS_BUTTON_DOUBLE_CLICK_TIME (200)
// <o> Long press time(ms) <100-65535>
// <i> Long press
// <i> Default: 1000
#define LS_BUTTON_LONG_PRESS_TIME (800)
// <o> Long long press time(ms) <1000-65535>
// <i> Long long press
// <i> Default: 1000
#define LS_BUTTON_LONG_LONG_PRESS_TIME (10000)
// <q> Automatic Scanning(Idle Sop, Interrupt Activation)
// <i> Whether to automatically disable scanning
// <0=> DISABLE
// <1=> ENABLE
#define LS_BUTTON_AUTOMATIC_SCANNING (0)
// </h>
/**************************************ADC**************************************/
// <h> ADC
// =======================
//
// <e> ADC0
#define LS_ADC0_EN (1)
// <o> Clk Divider
// <i> 0-PCLK/1, 1-PCLK/2, 2-PCLK/4, 3-PCLK/8, 4-PCLK/16, ..., 7-PCLK/128
#define LS_ADC0_CLK_DIV (5)
// <o> Sampling Number
// <i> Default: 10
#define LS_ADC0_SAMPLING_NUM (10)
// <q> ADC0 IRQ
#define LS_ADC0_IRQ_SEL (1)
// <e1.7> ADC0_CH
// <o0.0> ADC0_CH0
// <o0.1> ADC0_CH1
// <o0.2> ADC0_CH2
// <o0.3> ADC0_CH3
// <o0.4> ADC0_CH4
// <o0.5> ADC0_CH5
// <o0.6> ADC0_CH6
// <o0.7> ADC0_CH7 (sys_vcc)
#define LS_ADC0_CH (255)
// </e>
// <o> Timer Cycle
// <i> Default: 100ms
#define LS_ADC0_TIMER_CYCLE_MS (228)
// </e>
// <h> Resistance Information
// <h> Thermistor
// <o> Pull Up Resistance Value
// <i> Default: 100
// <i> Unit: KOhm
#define LS_THERMISTOR_PULL_UP_VAL (100)
// <o> Coefficient corresponding to NTC resistance
// <i> Default: 0 (x*1000)
#define LS_THERMISTOR_NTC_K (4250)
// <o> Reference voltage
// <i> Default: 3300 (x*1000)
#define LS_THERMISTOR_REFERENCE_VOLTAGE (2700)
// </h>
// <h> LDR
// <i> Photosensitive resistance
// <o> Pull Up Resistance Value
// <i> Default: 680
// <i> Unit: KOhm
#define LS_LDR_PULL_UP_VAL (680)
// <o> Reference voltage
// <i> Default: 3300 (x*1000)
#define LS_LDR_REFERENCE_VOLTAGE (2700)
// </h>
// <h> Power resistance
// <i> Power supply resistance
// <o> Pull Up Resistance Value
// <i> Default: 300000
// <i> Unit: KOhm
#define LS_POWER_PULL_UP_VAL (300)
// <o> Pull Down Resistance Value
// <i> Default: 100
// <i> Unit: KOhm
#define LS_POWER_PULL_DOWN_VAL (300)
// <o> Reference voltage
// <i> Default: 3300 (x*1000)
#define LS_POWER_REFERENCE_VOLTAGE (2700)
// </h>
// </h>
// </h>
/**************************************I2C**************************************/
// <h> I2C
// =======================
// <e> I2C0
#define LS_I2C0_EN (0)
// <o> I2C0 SPEED uint khz
// <i> Default: 100 khz
#define LS_I2C0_SPEED_RATE (400)
// </e>
// <e> I2C1
#define LS_I2C1_EN (0)
// <o> I2C1 SPEED uint khz
// <i> Default: 100 khz
#define LS_I2C1_SPEED_RATE (100)
// </e>
// <e> I2C2
#define LS_I2C2_EN (0)
// <o> I2C2 SPEED uint khz
// <i> Default: 100 khz
#define LS_I2C2_SPEED_RATE (100)
// </e>
// </h>
/**************************************UART*************************************/
// <h> UART
// =======================
// <e> UART0
#define LS_UART0_EN (1)
// <o> UART0 Baud Rate
// <i> Default: 115200
// <9600 => 9600
// <19200 => 19200
// <57600 => 57600
// <115200 => 115200
#define LS_UART0_BAUD_RATE (115200)
// <o> UART0 Working mode
// <i> Default: full duplex
// <0 => Full Duplex
// <1 => Half Duplex
#define LS_UART0_WORK_MODE (0)
// <o> UART0 RX cache size
// <i> Default: 256
#define LS_UART0_CACHE_SIZE (64)
// </e>
// <e> UART1
#define LS_UART1_EN (0)
// <o> UART1 Baud rate
// <i> Default: 115200
// <9600 => 9600
// <19200 => 19200
// <57600 => 57600
// <115200 => 115200
#define LS_UART1_BAUD_RATE (115200)
// <o> UART1 Working mode
// <i> Default: full duplex
// <0 => Full Duplex
// <1 => Half Duplex
#define LS_UART1_WORK_MODE (0)
// <o> UART1 RX cache size
// <i> Default: 256
#define LS_UART1_CACHE_SIZE (256)
// </e>
// <e> UART2
#define LS_UART2_EN (0)
// <o> UART2 Baud Rate
// <i> Default: 115200
// <9600 => 9600
// <19200 => 19200
// <57600 => 57600
// <115200 => 115200
#define LS_UART2_BAUD_RATE (115200)
// <o> UART2 Working Mode
// <i> Default: full duplex
// <0 => Full Duplex
// <1 => Half Duplex
#define LS_UART2_WORK_MODE (0)
// <o> UART2 RX Cache Size
// <i> Default: 256
#define LS_UART2_CACHE_SIZE (256)
// </e>
// <o> Printf
// <i> Default: UART0
// <0=> UART0
// <1=> UART1
// <2=> UART2
#define LS_FUART_PRINT (0)
// </h>
/**************************************PWM**************************************/
// <h> PWM
// =======================
// <e> TIM1
// <i> pwm hz = sys_clock / (Prescaler+1) / (Period+1)
// <i> 3125 hz = 24000000 / (63+1) / (119+1)
#define LS_TIM1_EN (1)
// <o> Prescaler
// <i> Default: 63
#define LS_TIM1_PRESCALER (63)
// <o> Period
// <i> Default: 119
#define LS_TIM1_PERIOD (119)
// <o> Level logic
// <i> Reverse --> low level light up
// <i> Forward --> high level light up
// <0=> Reverse
// <1=> Forward
#define LS_TIM1_LEVEL_LOGIC (1)
// <q> TIM1_CH1 (PWM0)
// <i> Default: DISABLE
// <0=> DISABLE
// <1=> ENABLE
#define LS_PWM0_EN (1)
// <q> TIM1_CH2 (PWM1)
// <i> Default: DISABLE
// <0=> DISABLE
// <1=> ENABLE
#define LS_PWM1_EN (1)
// <q> TIM1_CH3 (PWM2)
// <i> Default: DISABLE
// <0=> DISABLE
// <1=> ENABLE
#define LS_PWM2_EN (1)
// <q> TIM1_CH4 (PWM3)
// <i> Default: DISABLE
// <0=> DISABLE
// <1=> ENABLE
#define LS_PWM3_EN (1)
// </e>
// <e> TIM2
// <i> pwm hz = sys_clock / (Prescaler+1) / (Period+1)
// <i> 3125 hz = 24000000 / (63+1) / (119+1)
#define LS_TIM2_EN (1)
// <o> Prescaler
// <i> Default: 63
#define LS_TIM2_PRESCALER (63)
// <o> Period
// <i> Default: 119
#define LS_TIM2_PERIOD (119)
// <o> Level logic
// <i> Reverse --> low level light up
// <i> Forward --> high level light up
// <0=> Reverse
// <1=> Forward
#define LS_TIM2_LEVEL_LOGIC (1)
// <q> TIM2_CH1 (PWM4)
// <i> Default: DISABLE
// <0=> DISABLE
// <1=> ENABLE
#define LS_PWM4_EN (1)
// <q> TIM2_CH2 (PWM5)
// <i> Default: DISABLE
// <0=> DISABLE
// <1=> ENABLE
#define LS_PWM5_EN (1)
// <q> TIM2_CH3 (PWM6)
// <i> Default: DISABLE
// <0=> DISABLE
// <1=> ENABLE
#define LS_PWM6_EN (1)
// <q> TIM2_CH4 (PWM7)
// <i> Default: DISABLE
// <0=> DISABLE
// <1=> ENABLE
#define LS_PWM7_EN (1)
// </e>
// </h>
/*************************************Memory************************************/
// <h> Memory
// =======================
// <o> Memory SIZE
#define LS_MEMORY_SIZE (512+128)
// </h>
/*************************************BOOT************************************/
// <h> BootLoader
// =======================
// <q> BOOT_SUPPORT
#define BOOT_SUPPORT (1)
// <s> chip ic
#define CHIP_IC "CX32L003"
// <s> version info
#define VERSION_INFO "0.9"
// </h>
//------------- <<< end of configuration section >>> -----------------------
/*********************************[业务引脚命令]*******************************/
#define LS_IO_LED_IND_ID (11)
/********************************[FLASH INFO]*********************************/
#define LS_FLASH_APP_ADDR (LS_FLASH_START_ADDR + LS_FLASH_BOOT_SIZE)
#define LS_FLASH_APP_SIZE (LS_FLASH_MAX_SIZE - LS_FLASH_BOOT_SIZE - (LS_FLASH_KV_PAGE * LS_FLASH_PAGE_SIZE))
#define LS_FLASH_OTA_ADDR (LS_FLASH_APP_ADDR + LS_FLASH_APP_SIZE / 2)
#define LS_FLASH_END_ADDR (LS_FLASH_START_ADDR + LS_FLASH_MAX_SIZE)
#define LS_KV_BASE_ADDR (LS_FLASH_END_ADDR - (LS_FLASH_KV_PAGE * LS_FLASH_PAGE_SIZE))
#define LS_KV_BACK_ADDR (LS_KV_BASE_ADDR + (LS_FLASH_KV_PAGE - 1) * LS_FLASH_PAGE_SIZE)
#define LS_OPTION_BYTES_ADDR (0x08000000)
#define LS_KV_KEY_BOOT_INFO 0x01
#define LS_KV_KEY_POWER_INFO 0x02
#define LS_KV_KEY_USER_INFO 0x03
#define LS_KV_KEY_UID 0x04
#define LS_KV_KEY_IO_INFO 0x05
#endif- 功能裁剪
五、简单讲解功能
(1) 引用ATCMD
- 查询IO信息： AT+IOINFO?
返回：IO版本,是否支持保存,IO总数量
static int atcmd_get_io_info(atcmd_pack_t *pack) {
uint8_t buff[60] = {0};
snprintf((char*)buff, 60, "io_ver:%s,save_support:%d,io_num:%d",
IO_VERSION, g_io.flag.save_support, LS_IO_NUM);
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
return 0;
}
ATCMD_INIT("AT+IOINFO?", atcmd_get_io_info);- 当前内存使用情况： AT+MEMINFO?
使用值,总数量 （单位：byte）
static int atcmd_get_mem_info(atcmd_pack_t *pack) {
uint8_t buff[60] = {0};
mem_info_t* temp = os_get_memory_info();
if (temp != NULL) {
snprintf((char*)buff, 60, "%d,%d", temp->used, temp->size);
}
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
return 0;
}
ATCMD_INIT("AT+MEMINFO?", atcmd_get_mem_info);- IO事件：AT+IOEVENT?
返回全部IO事件状态
typedef enum {
IO_EVENT_NULL = 0,
IO_EVENT_IO_LOW, // 中断事件
IO_EVENT_IO_HIGH,
IO_EVENT_IO_KEY_SINGLE_CLICK, // 按键事件
IO_EVENT_IO_KEY_TWO_CLICK, // 双击
IO_EVENT_IO_KEY_LONG_PRESS, // 长按3秒
IO_EVENT_IO_KEY_LONG_LONG_PRESS, // 长按10秒
} io_event_t;
static int atcmd_get_event(atcmd_pack_t *pack) {
uint8_t buff[LS_IO_NUM * 2 + 10] = {0};
for (uint8_t i = 0; i < LS_IO_NUM; i++) {
char temp = g_io.func[i].io_event + '0';
strncat((char*)buff, &temp, 1);
if (i != LS_IO_NUM - 1)
strncat((char*)buff, ",", 1);
}
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
clean_signal_irq();
return 0;
}
ATCMD_INIT("AT+IOEVENT?", atcmd_get_event);- IO当前配置类型：AT+IOCFGALL?
static int atcmd_io_cfg_get_all(atcmd_pack_t *pack) {
char buff[LS_IO_NUM*2 + 10] = {0};
char temp[5] = {0};
uint8_t len = 0;
for (uint8_t i = 0; i < LS_IO_NUM; i++) {
len = snprintf(temp, 5, "%d", g_io.type[i]);
strncat(buff, temp, len);
if (i != LS_IO_NUM - 1)
strncat(buff, ",", 1);
}
strcat(buff, AT_OK);
pack->reply((uint8_t*)buff, strlen(buff));
return 0;
}
ATCMD_INIT("AT+IOCFGALL?", atcmd_io_cfg_get_all);- 配置IO类型：AT+IOCFGALL=18,19,1,1,1,1,1,1,1,1,1,1,1,1,38,37
这里填写的是IO索引表的序号(参考：一、界面介绍) - 设置IO高低电平：AT+IOALL=1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1
只对输出类型引脚有效
static int atcmd_set_io_all(atcmd_pack_t *pack) {
uint8_t argc[LS_IO_NUM] = {0};
char *arg; // 临时存放值
uint8_t cnt = 0;
uint8_t buff[20] = {0};
arg = strtok((char*)(pack->data), ",");
while (arg != NULL) {
argc[cnt++] = (uint8_t)atoi(arg);
arg = strtok(NULL, ",");
}
pack->argc = cnt;
if (pack->argc != LS_IO_NUM) {
strcat((char*)buff, AT_ARGCERR);
pack->reply(buff, strlen((char*)buff));
return -1;
}
for (uint8_t i = 0; i < LS_IO_NUM; i++) {
if (g_io.type[i] == IO_TYPE_OUT_PP)
bsp_gpio_set_pin(g_io.cfg[i].port, g_io.cfg[i].pin, argc[i]);
}
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
return 0;
}
ATCMD_INIT("AT+IOALL=", atcmd_set_io_all);- 当前IO高低电平：AT+IO?
static int atcmd_get_io(atcmd_pack_t *pack) {
uint8_t buff[LS_IO_NUM * 2 + 20] = {0};
for (uint8_t i = 0; i < LS_IO_NUM; i++) {
char temp = (uint8_t)bsp_gpio_get_state(g_io.cfg[i].port, g_io.cfg[i].pin) + '0';
strncat((char*)buff, &temp, 1);
if (i != LS_IO_NUM - 1)
strncat((char*)buff, ",", 1);
}
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
return 0;
}
ATCMD_INIT("AT+IO?", atcmd_get_io);-
IO任务：
查询任务：AT+IO_TASK?
设置IO任务基准时间：AT+IO_TIMER_MS=1,10
设置IO任务：AT+IO_TASK=0,1,0,20,0,40,1,11
设置周期任务 =<task_id>,<is_valid>,<is_repeat>,<start_time>,<start_task_event>,<stop_time>,<stop_task_event>,<IO_ID>
extern os_timer_id OS_TIMER_ID(app_io);
// 设置周期任务的基准时间 =<off/on>,<ms>
static int atcmd_set_io_timer_ms(atcmd_pack_t *pack) {
uint32_t argc[1] = {0};
uint8_t buff[40] = {0};
pack->argc = sscanf((char*)(pack->data), "%d", &argc[1]);
if (pack->argc != 1) return -1;
// 先停止周期任务，并将任务全部取消。
OS_TIMER_STOP(app_io);
for (uint8_t i = 0; i < LS_APP_IO_TIMER_NUM; i++) {
g_io.task[i].is_valid = 0;
}
if (argc[0]) {
if (os_timer_restart(OS_TIMER_ID(app_io), argc[0]) != OS_OK)
strcat((char*)buff, "io timer restart fail");
g_io.timer_io_time_ms = argc[0];
} else {
if (os_timer_stop(OS_TIMER_ID(app_io)) != OS_OK)
strcat((char*)buff, "io timer stop fail");
}
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
return 0;
}
// 设置周期任务 =<task_id>,<is_valid>,<is_repeat>,<start_time>,<start_task_event>,<stop_time>,<stop_task_event>,<IO_ID>
static int atcmd_set_task_func(atcmd_pack_t *pack) {
uint8_t buff[30] = {0};
if (!g_io.flag.timer_support) {
strcat((char*)buff, AT_NONSUPPORT);
pack->reply(buff, strlen((char*)buff));
return -1;
}
uint32_t argc[16] = {0};
pack->argc = sscanf((char*)(pack->data), "%d,%d,%d,%d,%d,%d,%d,%d,%d,%d,%d,%d,%d,%d,%d,%d",
&argc[0], &argc[1], &argc[2], &argc[3],
&argc[4], &argc[5], &argc[6], &argc[7],
&argc[8], &argc[9], &argc[10], &argc[11],
&argc[12], &argc[13], &argc[14], &argc[15]);
if (pack->argc / 8 > 2 || pack->argc / 8 < 1) {
strcat((char*)buff, AT_ARGCERR);
pack->reply(buff, strlen((char*)buff));
return -1;
}
OS_TIMER_STOP(app_io);
for (uint8_t i = 0; i < pack->argc / 8; i++) {
g_io.task[argc[0 + i * 8]].is_valid = argc[1 + i * 8];
g_io.task[argc[0 + i * 8]].is_repeat = argc[2 + i * 8];
g_io.task[argc[0 + i * 8]].start_time = argc[3 + i * 8];
g_io.task[argc[0 + i * 8]].start_task_event = argc[4 + i * 8];
g_io.task[argc[0 + i * 8]].stop_time = argc[5 + i * 8];
g_io.task[argc[0 + i * 8]].stop_task_event = argc[6 + i * 8];
g_io.task[argc[0 + i * 8]].id = argc[7 + i * 8];
if (g_io.type[argc[7 + i * 8]] != IO_TYPE_OUT_PP) { // 周期任务目标，会被强制设置为输出
uint8_t temp = IO_TYPE_OUT_PP;
io_cfg(argc[7 + i * 8], (io_type_t *)&temp, NULL);
g_io.type[argc[7 + i * 8]] = temp;
g_io.flag.write_in = 1;
}
g_io.task[argc[0 + i*8]].countdown = 0;
}
if (os_timer_restart(OS_TIMER_ID(app_io), g_io.timer_io_time_ms) != OS_OK) {
strcat((char*)buff, "io timer restart fail");
} else
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
return 0;
}
// 得到周期任务 =<task_id>,<is_valid>,<is_repeat>,<start_time>,<start_task_event>,<stop_time>,<stop_task_event>,<IO_ID>
static int atcmd_get_task_func(atcmd_pack_t *pack) {
uint8_t buff[30] = {0};
for (uint8_t i = 0; i < LS_APP_IO_TIMER_NUM; i++) {
snprintf((char *)buff, 30, "%d,%d,%d,%d,%d,%d,%d,%d\r\n",
i, g_io.task[i].is_valid, g_io.task[i].is_repeat,
g_io.task[i].start_time, g_io.task[i].start_task_event,
g_io.task[i].stop_time, g_io.task[i].stop_task_event, g_io.task[i].id);
pack->reply(buff, strlen((char*)buff));
}
pack->reply((uint8_t *)AT_OK, strlen(AT_OK));
return 0;
}
ATCMD_INIT("AT+IO_TIMER_MS=", atcmd_set_io_timer_ms);
ATCMD_INIT("AT+IO_TASK=", atcmd_set_task_func);
ATCMD_INIT("AT+IO_TASK?", atcmd_get_task_func);- ADC
AT+ADC0_CFG?
AT+ADC0_TIMER_MS=300
AT+ADC0_START
AT+ADC0_STOP
AT+GET_ADC0_VAL?
AT+ADC0_CFG=?
AT+ADC0_CFG=1,10
#include "bsp_adc.h"
extern bsp_adc_cfg_t g_adc0_cfg;
extern os_timer_id OS_TIMER_ID(adc0_collection);
extern uint32_t g_adc0_timer_ms;
static int atcmd_adc0_cfg_help(atcmd_pack_t *pack) {
char buff[60] = {0};
snprintf(buff, 60, "AT+ADC0_CFG=<clk_sel(0-7)>,<sample_num(0-255)>\r\n");
strcat(buff, AT_OK);
pack->reply((uint8_t*)buff, strlen(buff));
return 0;
}
static int atcmd_get_adc0_cfg(atcmd_pack_t *pack) {
char buff[30] = {0};
snprintf(buff, 30, "%d,%d\r\n", g_adc0_cfg.clk_sel, g_adc0_cfg.sample_num);
strcat(buff, AT_OK);
pack->reply((uint8_t*)buff, strlen(buff));
return 0;
}
static int atcmd_set_adc0_cfg(atcmd_pack_t *pack) {
uint32_t argc[2] = {0};
char buff[20] = {0};
pack->argc = sscanf((char*)(pack->data), "%d,%d", &argc[0], &argc[1]);
if (pack->argc != 2) {
strcat(buff, AT_ARGCERR);
pack->reply((uint8_t*)buff, strlen(buff));
return -2;
}
bsp_adc0_deinit();
g_adc0_cfg.clk_sel = (uint8_t)argc[0];
g_adc0_cfg.sample_num = argc[1];
if (bsp_adc0_init(&g_adc0_cfg)) {
strcat(buff, AT_ERROR);
} else {
strcat(buff, AT_OK);
}
pack->reply((uint8_t*)buff, strlen(buff));
return 0;
}
static int atcmd_set_adc0_timer_ms(atcmd_pack_t *pack) {
uint32_t argc[1] = {0};
uint8_t buff[40] = {0};
pack->argc = sscanf((char*)(pack->data), "%d", &argc[0]);
if (pack->argc != 1) return -1;
// 先停止周期任务，并将任务全部取消。
OS_TIMER_STOP(adc0_collection);
if (argc[0]) {
if (os_timer_restart(OS_TIMER_ID(adc0_collection), argc[0]) != OS_OK)
strcat((char*)buff, "adc0 timer restart fail");
g_adc0_timer_ms = argc[0];
} else {
if (os_timer_stop(OS_TIMER_ID(adc0_collection)) != OS_OK)
strcat((char*)buff, "adc0 timer stop fail");
}
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
return 0;
}
static int atcmd_adc0_start(atcmd_pack_t *pack) {
uint8_t buff[40] = {0};
if (os_timer_restart(OS_TIMER_ID(adc0_collection), g_adc0_timer_ms) != OS_OK)
strcat((char*)buff, "adc0 timer restart fail");
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
return 0;
}
static int atcmd_adc0_stop(atcmd_pack_t *pack) {
uint8_t buff[40] = {0};
if (os_timer_stop(OS_TIMER_ID(adc0_collection)) != OS_OK)
strcat((char*)buff, "adc0 timer stop fail");
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
return 0;
}
static int atcmd_get_adc0_val(atcmd_pack_t *pack) {
uint8_t buff[60] = {0};
snprintf((char *)buff, 60, "%d,%d,%d,%d,%d,%d,%d,%d\r\n",
bsp_adc0_get_ch_val(0), bsp_adc0_get_ch_val(1), bsp_adc0_get_ch_val(2), bsp_adc0_get_ch_val(3),
bsp_adc0_get_ch_val(4), bsp_adc0_get_ch_val(5), bsp_adc0_get_ch_val(6), bsp_adc0_get_ch_val(7));
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
return 0;
}
static int atcmd_get_adc0_designated_val(atcmd_pack_t *pack) {
uint32_t argc[1];
uint8_t buff[30] = {0};
pack->argc = sscanf((char*)(pack->data), "%d", &argc[0]);
if (pack->argc != 1) return -1;
snprintf((char *)buff, 30, "%d", bsp_adc0_get_ch_val(argc[0]));
strcat((char*)buff, AT_OK);
pack->reply(buff, strlen((char*)buff));
return 0;
}
ATCMD_INIT("AT+ADC0_TIMER_MS=", atcmd_set_adc0_timer_ms);
ATCMD_INIT("AT+ADC0_START", atcmd_adc0_start);
ATCMD_INIT("AT+ADC0_STOP", atcmd_adc0_stop);
ATCMD_INIT("AT+GET_ADC0_VAL=", atcmd_get_adc0_designated_val);
ATCMD_INIT("AT+GET_ADC0_VAL?", atcmd_get_adc0_val);
ATCMD_INIT("AT+ADC0_CFG=?", atcmd_adc0_cfg_help);
ATCMD_INIT("AT+ADC0_CFG=", atcmd_set_adc0_cfg);
ATCMD_INIT("AT+ADC0_CFG?", atcmd_get_adc0_cfg);- PWM
AT+PWM=0,10
AT+TIM1_CFG=7,99,0
AT+TIM1_CFG=?
AT+PWM_TASK=
#include "bsp_pwm.h"
#include "bsp_tim.h"
#if LS_TIM1_EN
extern bsp_tim_cfg_t g_tim1_cfg;
static int atcmd_set_tim1_cfg_help(atcmd_pack_t *pack) {
char buff[85] = {0};
snprintf(buff, 60, "AT+TIM1_CFG=<prescaler(0-65534)>,<period(0-65534)>,<level_logic(0-1)>\r\n");
strcat(buff, AT_OK);
pack->reply((uint8_t*)buff, strlen(buff));
return 0;
}
static int atcmd_set_tim1_cfg(atcmd_pack_t *pack) {
uint32_t argc[3] = {0};
char buff[10] = {0};
pack->argc = sscanf((char*)(pack->data), "%d,%d,%d", &argc[0], &argc[1], &argc[2]);
if (pack->argc != 3) {
strcat(buff, AT_ARGCERR);
pack->reply((uint8_t*)buff, strlen(buff));
return -2;
}
bsp_tim1_pwm_deinit();
g_tim1_cfg.prescaler = (uint16_t)argc[0];
g_tim1_cfg.period = (uint16_t)argc[1];
g_tim1_cfg.level_logic = (uint8_t)argc[2];
if (bsp_tim1_pwm_init(&g_tim1_cfg)) {
strcat(buff, AT_ERROR);
} else {
strcat(buff, AT_OK);
}
pack->reply((uint8_t*)buff, strlen(buff));
return 0;
}
ATCMD_INIT("AT+TIM1_CFG=?", atcmd_set_tim1_cfg_help);
ATCMD_INIT("AT+TIM1_CFG=", atcmd_set_tim1_cfg);
#endif
#if LS_TIM2_EN
extern bsp_tim_cfg_t g_tim2_cfg;
static int atcmd_set_tim2_cfg_help(atcmd_pack_t *pack) {
char buff[85] = {0};
snprintf(buff, 60, "AT+TIM2_CFG=<prescaler(0-65534)>,<period(0-65534)>,<level_logic(0-1)>\r\n");
strcat(buff, AT_OK);
pack->reply((uint8_t*)buff, strlen(buff));
return 0;
}
static int atcmd_set_tim2_cfg(atcmd_pack_t *pack) {
uint32_t argc[3] = {0};
char buff[10] = {0};
pack->argc = sscanf((char*)(pack->data), "%d,%d,%d", &argc[0], &argc[1], &argc[2]);
if (pack->argc != 3) {
strcat(buff, AT_ARGCERR);
pack->reply((uint8_t*)buff, strlen(buff));
return -2;
}
bsp_tim2_pwm_deinit();
g_tim2_cfg.prescaler = (uint16_t)argc[0];
g_tim2_cfg.period = (uint16_t)argc[1];
g_tim2_cfg.level_logic = (uint8_t)argc[2];
if (bsp_tim2_pwm_init(&g_tim2_cfg)) {
strcat(buff, AT_ERROR);
} else {
strcat(buff, AT_OK);
}
pack->reply((uint8_t*)buff, strlen(buff));
return 0;
}
ATCMD_INIT("AT+TIM2_CFG=?", atcmd_set_tim2_cfg_help);
ATCMD_INIT("AT+TIM2_CFG=", atcmd_set_tim2_cfg);
#endif
static int atcmd_set_pwm_val_help(atcmd_pack_t *pack) {
char buff[60] = {0};
snprintf(buff, 60, "AT+PWM=<ch(0-7)>,<val(0-65535)>\r\n");
strcat(buff, AT_OK);
pack->reply((uint8_t*)buff, strlen(buff));
return 0;
}
static int atcmd_set_pwm_val(atcmd_pack_t *pack) {
uint32_t argc[2] = {0};
uint8_t buff[10] = {0};
pack->argc = sscanf((char*)(pack->data), "%d,%d", &argc[0], &argc[1]);
if (pack->argc != 2) {
strcat((char*)buff, AT_ARGCERR);
pack->reply(buff, strlen((char*)buff));
return -2;
}
if (bsp_pwm_set_pulse(argc[0], argc[1])) {
strcat((char*)buff, AT_ERROR);
} else {
strcat((char*)buff, AT_OK);
}
pack->reply(buff, strlen((char*)buff));
return 0;
}
ATCMD_INIT("AT+PWM=?", atcmd_set_pwm_val_help);
ATCMD_INIT("AT+PWM=", atcmd_set_pwm_val);gitee地址：LiSunSDK开源地址