我按照“快速上手”重新烧录了1月6号的nand中的的uboot、内核还有文件系统。
Qtopia烧录后，就重新启动，发生了下面的情况：
U-Boot 1.1.6 (Jan 4 2011 - 21:24:28) for SMDK6410
CPU: S3C6410@800MHz
Fclk = 800MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (SYNC Mode)
Board: SMDK6410
DRAM: 256 MB
Flash: 0 kB
NAND: Maf. ID is d3
1024 MB
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x40000, size 0x300000
3145728 bytes read: OK
Boot with zImage
Starting kernel ...
Uncompressing Linux...................................................................................................................................................................................... done, booting the kernel.
Linux version 2.6.28.6 (figo@figo-desktop) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) #721 PREEMPT Sun Jan 2 16:59:05 CST 2011
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SMDK6410
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101) cpu还有id 啊
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C64XX: PLL settings, A=800000000, M=532000000, E=24000000
S3C64XX: HCLKx2=266666666, HCLK=133333333, PCLK=66666666
div1: 00000555
mout_apll: source is fout_apll (1), rate is 800000000
mout_epll: source is fout_epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 532000000
mmc_bus: source is dout_mpll (1), rate is 44333333
mmc_bus: source is dout_mpll (1), rate is 44333333
mmc_bus: source is dout_mpll (1), rate is 44333333
usb-host-bus: source is mout_epll (0), rate is 24000000
uclk1: source is dout_mpll (1), rate is 66500000
spi_epll: source is mout_epll (0), rate is 24000000
spi_epll: source is mout_epll (0), rate is 24000000
sclk_audio0: source is mout_epll (0), rate is 24000000
sclk_audio1: source is mout_epll (0), rate is 24000000
sclk_audio2: source is mout_epll (0), rate is 24000000
irda-bus: source is mout_epll (0), rate is 24000000
s3c64xx: 10485760 bytes SDRAM reserved for fimc at 0x50810000
s3c64xx: 8388608 bytes SDRAM reserved for pp at 0x51210000
s3c64xx: 8388608 bytes SDRAM reserved for tv at 0x51a10000
s3c64xx: 6291456 bytes SDRAM reserved for mfc at 0x52210000
s3c64xx: 8388608 bytes SDRAM reserved for jpeg at 0x52810000
s3c64xx: 8388608 bytes SDRAM reserved for cmm at 0x53010000
s3c64xx: 19922944 bytes SDRAM reserved for s3c-g3d at 0x53810000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 56896
Kernel command line: setenv bootargs noinitrd mem=224M console=ttySAC0 init=/init ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs 每次都要打印下环境变量么？
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 224MB = 224MB total
Memory: 152064KB available (5308K code, 928K data, 152K init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 797.90 BogoMIPS (lpj=1994752)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 288 bytes
NET: Registered protocol family 16
S3C6410 Power Management, (c) 2008 Samsung Electronics
S3C6410: Initialising architecture
S3C DMA-pl080 Controller Driver, (c) 2006-2007 Samsung Electronics
Total 32 DMA channels will be initialized.
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
S3C64XX ADC driver, (c) 2008 Samsung Electronics
S5P64XX ADC driver successfully probed
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
yaffs Jan 2 2011 16:55:25 Installing. yaffs是个文件系统么
msgmni has been set to 297
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
LCD屏幕的初始化 问题就是处在这里。 初始化是失败的，没有fb那一套。
S3C_LCD clock got enabled :: 133.333 Mhz
video output type detect error!! 没能识别到LCD的类型
Failed to allocate video RAM: -12 不能给LCD分配显存RAM
Trying to free already-free IRQ 62 释放已经释放的中断IRQ 62
s3c-lcd: probe of s3c-lcd failed with error -12
ledsinitialized.
s3c-aes initialized
S3C AES Drvier 各个设备的初始化
下面应该是串行设备的初始化，串口的吧。 4个串口啊。
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
s3c6400-uart.2: s3c2410_serial2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
s3c6400-uart.3: s3c2410_serial3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
brd: module loaded
loop: module loaded
nbd: registered device at major 43
pmem: 1 init
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
mcp251x_init(1063): start
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
CSLIP: code copyright 1989 Regents of the University of California.
dm9000 Ethernet Driver 网卡驱动
eth0: dm9000 at ce890000,ce890004 IRQ 108 MAC: 00:22:12:34:56:90
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
console [netcon0] enabled
netconsole: network logging started
Linux video capture interface: v2.00
s3c-fimc: controller 0 registered successfully
s3c-fimc: controller 1 registered successfully
S3C6400 MFC Driver, (c) 2007 Samsung Electronics
S3C6400 MFC Driver, (c) 2007 Samsung Electronics
S3C PostProcessor Driver v3.12, (c) 2009 Samsung Electronics
S3C6410 TV encoder Driver, (c) 2008 Samsung Electronics
S3C6410 TV encoder Driver init OK.
S3C6410 TV scaler Driver, (c) 2008 Samsung Electronics
S3C6410 TV scaler Driver init OK.
S3C Rotator Driver, (c) 2008 Samsung Electronics
s3c_rotator_probe called
s3c_rotator_probe success
S3C JPEG Driver, (c) 2007 Samsung Electronics
s3c-g2d: Driver loaded succesfully
s3c-g2d: Module initialized.
s3c-g3d: Driver loaded succesfully
s3c-g3d: Module initialized.
S3C CMM Driver, (c) 2008 Samsung Electronics
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
Creating 2 MTD partitions on "NAND 1GiB 3,3V 8-bit":
文件系统的位置
0x00400000-0x00800000 : "cramfs"
0x00800000-0x40000000 : "ubifs"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 262144 bytes (256 KiB)
UBI: logical eraseblock size: 258048 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "ubifs"
UBI: MTD device size: 1016 MiB
UBI: number of good PEBs: 4064
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 4064
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 2/1
UBI: background thread "ubi_bgt0d" started, PID 1048
spi->irq = 151
Max,Min-Speed [33333333, 130208]Hz
Irq=80 IOmem=[0x7f00bfff-0x7f00b000] DMA=[Rx-33, Tx-34]
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 79, io mem 0x74300000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android adb driver
Registered gadget driver 'android_adb'
mice: PS/2 mouse device common for all mice
gpio-keys init
input: gpio-keys as /devices/platform/gpio-keys/input/input0
S3C Touchscreen driver, (c) 2008 Samsung Electronics 触摸屏。
S3C TouchScreen got loaded successfully : 12 bits
input: S3C TouchScreen as /devices/virtual/input/input1
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410_rtc: tick irq 34, alarm irq 92
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 378 KHz
[CAMERA]camera_attach_adapter. 摄像头也有了。
parent clock for camera: 266.666 MHz, divisor: 11
parent clock for camera: 266.666 MHz, divisor: 11
parent clock for camera: 266.666 MHz, divisor: 9
CAMERA TVP5150 attached successfully
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
at24 0-0050: 1024 byte 24c08 EEPROM (writable)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (44333333 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
sdhci: card inserted.
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (44333333 Hz)
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
sdhci: card removed.
ASoC version 0.13.2 声卡驱动
WM9713/WM9714 SoC Audio Codec 0.15
playback: 1, capture : 1
asoc: AC97 HiFi <-> s3c64xx-ac97 mapping ok
[WM9713]Open speaker volume.
ALSA device list:
#0: SMDK6400 (WM9713)
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20081130 abi 8)
NET: Registered protocol family 29
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
s3c2410-rtc s3c2410-rtc: setting system clock to 2030-10-20 13:34:12 UTC (1918733652)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 1034514432 bytes (1010268 KiB, 986 MiB, 4009 LEBs)
UBIFS: journal size: 33546240 bytes (32760 KiB, 31 MiB, 130 LEBs)
UBIFS: media format: 4 (latest is 4)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 5182151 bytes (5060 KiB)
VFS: Mounted root (ubifs filesystem).
Freeing init memory: 152K
Failed to execute /init. Attempting defaults...
Try to bring eth0 interface up......eth0: link down
Done
Now,starting the qtopia-2.2.0....
Please press Enter to activate this console. Can't open framebuffer device /dev/fb0
Can't open framebuffer device /dev/fb0
driver cannot connect
[root@Real6410 Settings]# cat qpe.conf
[Appearance]
AlternateBase = #EEF5D6
Background = #eeeeee
BackgroundImage =
Base = #FFFFFF
Button = #F0F0F0
ButtonText = #000000
Decoration = Qtopia
FontFamily = helvetica
FontSize = 12
Foreground = #222222
Foreground_disabled = #BBBBBB
Highlight = #8BAC30
HighlightedText = #FFFFFF
IconSize = 16
Scheme = Qtopia
Shadow =
Style = Qtopia
Text = #000000
Text_disabled = #BBBBBB
Theme = qtopia.conf
[ApplicationPositions]
appearance = 0,0,376,421,1
calculator = 196,130,400,192,1
clock = 196,130,400,192,1
datebook = 196,130,400,192,0
fifteen = 116,70,240,108,1
hwsettings = 116,77,239,101,0
konqueror = 0,0,400,192,1
language = 258,83,276,269,0
launchersettings = 279,82,234,270,0
music = 196,130,400,192,1
parashoot = 116,70,240,108,1
penpad = 116,0,240,290,1
photoedit = 116,70,240,108,1
qasteroids = 116,70,240,108,1
snake = 116,70,240,108,1
solitaire = 196,130,400,192,1
videos = 116,60,240,128,1
worldtime = 196,130,400,192,1
[BatteryPower]
Brightness = 255
Dim = 1
Interval = 240
Interval_Dim = 20
Interval_LightOff = 30
LightOff = 0
Suspend = 1
[Date]
LongOrder = 273
Separator = /
ShortOrder = 273
[Keyboard]
[Rotation]
Cursor = 0
[Screensaver]
Brightness = 255
Dim = 1
Interval = 240
Interval_Dim = 20
Interval_LightOff = 30
LightOff = 0
Suspend = 1
[Startup]
FirstUse = 0
[StorageMonitor]
[Time]
[root@Real6410 Settings]#
删掉qpe.conf的方式也不管用。
条件export 什么的，那些路径也不管用。
组后，从uboot启动，有一个boot qtopia的选项。
然后跟直接从内核启动一样的过程，但是可以顺利看到企鹅了，应该是启动了qvfb，也就能进去 图形界面了。
后来启动都是正常的了。
我真是百思不得其解。
=====
还有，内部有个qt4的测试程序，里头有个调整触摸屏的，虽然也是重启，启动测试程序，和uboot里头的启动测试程序的方式一样，
但是，这个调整过后，如果调整错了，比如我点错了，在用uboot的调整，就是调不过来。只好，努力用这个程序，再次调整一次。
虽然看上去，和uboot里的程序调整一样。
难道是配置文件 的存放位置不同么？
好奇怪啊。
=======================
usb的鼠标能识别，但不能用。
下面是正常启动qtopia的过程和成功再次调整touchscreen的过程。
U-Boot 1.1.6 (Jan 4 2011 - 21:24:28) for SMDK6410
CPU: S3C6410@800MHz
Fclk = 800MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (SYNC Mode)
Board: SMDK6410
DRAM: 256 MB
Flash: 0 kB
NAND: Maf. ID is d3
1024 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x40000, size 0x300000
3145728 bytes read: OK
Boot with zImage
Starting kernel ...
Uncompressing Linux...................................................................................................................................................................................... done, booting the kernel.
Linux version 2.6.28.6 (figo@figo-desktop) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) #721 PREEMPT Sun Jan 2 16:59:05 CST 2011
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SMDK6410
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C64XX: PLL settings, A=800000000, M=532000000, E=24000000
S3C64XX: HCLKx2=266666666, HCLK=133333333, PCLK=66666666
div1: 00000555
mout_apll: source is fout_apll (1), rate is 800000000
mout_epll: source is fout_epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 532000000
mmc_bus: source is dout_mpll (1), rate is 44333333
mmc_bus: source is dout_mpll (1), rate is 44333333
mmc_bus: source is dout_mpll (1), rate is 44333333
usb-host-bus: source is mout_epll (0), rate is 24000000
uclk1: source is dout_mpll (1), rate is 66500000
spi_epll: source is mout_epll (0), rate is 24000000
spi_epll: source is mout_epll (0), rate is 24000000
sclk_audio0: source is mout_epll (0), rate is 24000000
sclk_audio1: source is mout_epll (0), rate is 24000000
sclk_audio2: source is mout_epll (0), rate is 24000000
irda-bus: source is mout_epll (0), rate is 24000000
s3c64xx: 10485760 bytes SDRAM reserved for fimc at 0x50810000
s3c64xx: 8388608 bytes SDRAM reserved for pp at 0x51210000
s3c64xx: 8388608 bytes SDRAM reserved for tv at 0x51a10000
s3c64xx: 6291456 bytes SDRAM reserved for mfc at 0x52210000
s3c64xx: 8388608 bytes SDRAM reserved for jpeg at 0x52810000
s3c64xx: 8388608 bytes SDRAM reserved for cmm at 0x53010000
s3c64xx: 19922944 bytes SDRAM reserved for s3c-g3d at 0x53810000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 56896
Kernel command line: noinitrd console=ttySAC0 ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs init=/init video=fb:WX4300F mem=224M ppp=none
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 224MB = 224MB total
Memory: 152064KB available (5308K code, 928K data, 152K init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 797.90 BogoMIPS (lpj=1994752)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 288 bytes
NET: Registered protocol family 16
S3C6410 Power Management, (c) 2008 Samsung Electronics
S3C6410: Initialising architecture
S3C DMA-pl080 Controller Driver, (c) 2006-2007 Samsung Electronics
Total 32 DMA channels will be initialized.
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
S3C64XX ADC driver, (c) 2008 Samsung Electronics
S5P64XX ADC driver successfully probed
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
yaffs Jan 2 2011 16:55:25 Installing. 这个文件系统
msgmni has been set to 297
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
S3C_LCD clock got enabled :: 133.333 Mhz 初始化LCD的时候，初始化fb设备。
LCD TYPE :: WX4300F will be initialized
Window[0] - FB1: map_video_memory: clear ff000000:0007f800
FB1: map_video_memory: dma=5d200000 cpu=ff000000 size=0007f800
Window[0] - FB2: map_video_memory: clear ff03fc00:0003fc00
FB2: map_video_memory: dma=5d23fc00 cpu=ff03fc00 size=0003fc00
Console: switching to colour frame buffer device 60x34
fb0: s3cfb frame buffer device
Window[1] - FB1: map_video_memory: clear ff080000:0003fc00
FB1: map_video_memory: dma=5d1c0000 cpu=ff080000 size=0003fc00
Window[1] - FB2: map_video_memory: clear ff09fe00:0001fe00
FB2: map_video_memory: dma=5d1dfe00 cpu=ff09fe00 size=0001fe00
fb1: s3cfb frame buffer device
Window[2] - FB1: map_video_memory: clear ff0c0000:0003fc00
FB1: map_video_memory: dma=5d280000 cpu=ff0c0000 size=0003fc00
fb2: s3cfb frame buffer device
Window[3] - FB1: map_video_memory: clear ff100000:0003fc00
FB1: map_video_memory: dma=5d2c0000 cpu=ff100000 size=0003fc00
fb3: s3cfb frame buffer device
ledsinitialized. lcd已经被初始化
s3c-aes initialized
S3C AES Drvier
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
s3c6400-uart.2: s3c2410_serial2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
s3c6400-uart.3: s3c2410_serial3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
brd: module loaded
loop: module loaded
nbd: registered device at major 43
pmem: 1 init
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
mcp251x_init(1063): start
PPP generic driver version 2.4.2 ppp拨号么
PPP Deflate Compression module registered
PPP BSD Compression module registered
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
CSLIP: code copyright 1989 Regents of the University of California.
dm9000 Ethernet Driver
eth0: dm9000 at ce890000,ce890004 IRQ 108 MAC: 00:22:12:34:56:90
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
console [netcon0] enabled
netconsole: network logging started
Linux video capture interface: v2.00
s3c-fimc: controller 0 registered successfully
s3c-fimc: controller 1 registered successfully
S3C6400 MFC Driver, (c) 2007 Samsung Electronics mfc驱动。
S3C6400 MFC Driver, (c) 2007 Samsung Electronics
S3C PostProcessor Driver v3.12, (c) 2009 Samsung Electronics
S3C6410 TV encoder Driver, (c) 2008 Samsung Electronics
S3C6410 TV encoder Driver init OK.
S3C6410 TV scaler Driver, (c) 2008 Samsung Electronics
S3C6410 TV scaler Driver init OK.
S3C Rotator Driver, (c) 2008 Samsung Electronics
s3c_rotator_probe called
s3c_rotator_probe success
S3C JPEG Driver, (c) 2007 Samsung Electronics
s3c-g2d: Driver loaded succesfully 2d驱动
s3c-g2d: Module initialized.
s3c-g3d: Driver loaded succesfully 3d驱动
s3c-g3d: Module initialized.
S3C CMM Driver, (c) 2008 Samsung Electronics
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
Creating 2 MTD partitions on "NAND 1GiB 3,3V 8-bit":
0x00400000-0x00800000 : "cramfs"
0x00800000-0x40000000 : "ubifs"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 262144 bytes (256 KiB)
UBI: logical eraseblock size: 258048 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "ubifs"
UBI: MTD device size: 1016 MiB
UBI: number of good PEBs: 4064
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 4064
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 2/1
UBI: background thread "ubi_bgt0d" started, PID 1053
spi->irq = 151
Max,Min-Speed [33333333, 130208]Hz
Irq=80
IOmem=[0x7f00bfff-0x7f00b000]
DMA=[Rx-33, Tx-34]
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1 usb驱动，但是usb不能用啊。
s3c2410-ohci s3c2410-ohci: irq 79, io mem 0x74300000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered. u盘的驱动
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems GSM的usb驱动
s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android adb driver linux的内核，还支持android哦，全能内核啊。
Registered gadget driver 'android_adb'
mice: PS/2 mouse device common for all mice
gpio-keys init
input: gpio-keys as /devices/platform/gpio-keys/input/input0
S3C Touchscreen driver, (c) 2008 Samsung Electronics 触摸屏驱动。
S3C TouchScreen got loaded successfully : 12 bits
input: S3C TouchScreen as /devices/virtual/input/input1
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410_rtc: tick irq 34, alarm irq 92
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 378 KHz
[CAMERA]camera_attach_adapter.
parent clock for camera: 266.666 MHz, divisor: 11
parent clock for camera: 266.666 MHz, divisor: 11
parent clock for camera: 266.666 MHz, divisor: 9
CAMERA TVP5150 attached successfully
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
at24 0-0050: 1024 byte 24c08 EEPROM (writable)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (44333333 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
sdhci: card inserted. SD卡，识别到已经插入了。
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (44333333 Hz)
sdhci: card removed.
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18rc3. ALSA出现了。
ASoC version 0.13.2
usb 1-1: new low speed USB device using s3c2410-ohci and address 2
WM9713/WM9714 SoC Audio Codec 0.15 声卡。
playback: 1, capture : 1
asoc: AC97 HiFi <-> s3c64xx-ac97 mapping ok
[WM9713]Open speaker volume.
ALSA device list:
#0: SMDK6400 (WM9713)
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20081130 abi 8)
NET: Registered protocol family 29
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ieee80211: 802.11 data/management/control stack, git-1.1.13 无线网卡？？？
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
s3c2410-rtc s3c2410-rtc: setting system clock to 2011-02-15 19:50:44 UTC (1297799444)
UBIFS: mounted UBI device 0, volume 0, name "rootfs" UBIFS是rootfs这个。
UBIFS: file system size: 1034514432 bytes (1010268 KiB, 986 MiB, 4009 LEBs)
UBIFS: journal size: 33546240 bytes (32760 KiB, 31 MiB, 130 LEBs)
UBIFS: media format: 4 (latest is 4)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 5182151 bytes (5060 KiB)
VFS: Mounted root (ubifs filesystem).
Freeing init memory: 152K
Failed to execute /init. Attempting defaults...
usb 1-1: configuration #1 chosen from 1 choice
input: PIXART USB OPTICAL MOUSE as /devices/platform/s3c2410-ohci/usb1/1-1/1-1:1.0/input/input2
generic-usb 0003:093A:2510.0001: input: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-s3c24xx-1/input0
Try to bring eth0 interface up......eth0: link down
Done
上面的一切都好之后，就可以顺利启动qtopia这个应用程序了。
调整触摸屏，也是一个应用程序。
Now,starting the qtopia-2.2.0....
Touch Screen has not been calibrate yet...
Please press Enter to activate this console. xres = 480, yres = 272
Took 10 samples...
Top left : X = 3002 Y = 1623
Took 8 samples...
Top right : X = 951 Y = 1617
Took 5 samples...
Bot right : X = 960 Y = 2479
Took 3 samples...
Bot left : X = 2981 Y = 2498
Took 7 samples...
Center : X = 1995 Y = 2067
611.656738 -0.186603 -0.001259
-268.805664 -0.001221 0.197989
Calibration constants: 40085536 -12229 -82 -17616448 -79 12975 65536
这个就是触摸屏调整的配置文件的存放位置
/etc/pointercal
Now reboot the system for saving the /etc/pointercal in flash
umount: can't remount none read-only
umount: none busy - remounted read-only
The system is going down NOW!
Sending SIGTERM to all processes
Sending SIGKILL to all processes
Requesting system reboot
RestartinOK
U-Boot 1.1.6 (Jan 4 2011 - 21:24:28) for SMDK6410
CPU: S3C6410@800MHz
Fclk = 800MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (SYNC Mode)
Board: SMDK6410
DRAM: 256 MB
Flash: 0 kB
NAND: Maf. ID is d3
1024 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x40000, size 0x300000
3145728 bytes read: OK
Boot with zImage
Starting kernel ...
Uncompressing Linux...................................................................................................................................................................................... done, booting the kernel.
Linux version 2.6.28.6 (figo@figo-desktop) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) #721 PREEMPT Sun Jan 2 16:59:05 CST 2011
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SMDK6410
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C64XX: PLL settings, A=800000000, M=532000000, E=24000000
S3C64XX: HCLKx2=266666666, HCLK=133333333, PCLK=66666666
div1: 00000555
mout_apll: source is fout_apll (1), rate is 800000000
mout_epll: source is fout_epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 532000000
mmc_bus: source is dout_mpll (1), rate is 44333333
mmc_bus: source is dout_mpll (1), rate is 44333333
mmc_bus: source is dout_mpll (1), rate is 44333333
usb-host-bus: source is mout_epll (0), rate is 24000000
uclk1: source is dout_mpll (1), rate is 66500000
spi_epll: source is mout_epll (0), rate is 24000000
spi_epll: source is mout_epll (0), rate is 24000000
sclk_audio0: source is mout_epll (0), rate is 24000000
sclk_audio1: source is mout_epll (0), rate is 24000000
sclk_audio2: source is mout_epll (0), rate is 24000000
irda-bus: source is mout_epll (0), rate is 24000000
s3c64xx: 10485760 bytes SDRAM reserved for fimc at 0x50810000
s3c64xx: 8388608 bytes SDRAM reserved for pp at 0x51210000
s3c64xx: 8388608 bytes SDRAM reserved for tv at 0x51a10000
s3c64xx: 6291456 bytes SDRAM reserved for mfc at 0x52210000
s3c64xx: 8388608 bytes SDRAM reserved for jpeg at 0x52810000
s3c64xx: 8388608 bytes SDRAM reserved for cmm at 0x53010000
s3c64xx: 19922944 bytes SDRAM reserved for s3c-g3d at 0x53810000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 56896
Kernel command line: noinitrd console=ttySAC0 ubi.mtd=1 root=ubi0:rootfs rootfstype=ubifs init=/init
video=fb:WX4300F mem=224M ppp=none 这里就识别到了屏幕，后头还有个初始化呢
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
console [ttySAC0] enabled 看来都是这个控制台。
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 224MB = 224MB total
Memory: 152064KB available (5308K code, 928K data, 152K init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 797.90 BogoMIPS (lpj=1994752)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 288 bytes
NET: Registered protocol family 16
S3C6410 Power Management, (c) 2008 Samsung Electronics
S3C6410: Initialising architecture 初始化体系结构
S3C DMA-pl080 Controller Driver, (c) 2006-2007 Samsung Electronics
Total 32 DMA channels will be initialized.
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
S3C64XX ADC driver, (c) 2008 Samsung Electronics
S5P64XX ADC driver successfully probed
NetWinder Floating Point Emulator V0.97 (double precision)
ashmem: initialized
yaffs Jan 2 2011 16:55:25 Installing.
msgmni has been set to 297
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
S3C_LCD clock got enabled :: 133.333 Mhz
lcd的初始化过程
LCD TYPE :: WX4300F will be initialized
Window[0] - FB1: map_video_memory: clear ff000000:0007f800
FB1: map_video_memory: dma=5d200000 cpu=ff000000 size=0007f800
Window[0] - FB2: map_video_memory: clear ff03fc00:0003fc00
FB2: map_video_memory: dma=5d23fc00 cpu=ff03fc00 size=0003fc00
Console: switching to colour frame buffer device 60x34
fb0: s3cfb frame buffer device
Window[1] - FB1: map_video_memory: clear ff080000:0003fc00
FB1: map_video_memory: dma=5d1c0000 cpu=ff080000 size=0003fc00
Window[1] - FB2: map_video_memory: clear ff09fe00:0001fe00
FB2: map_video_memory: dma=5d1dfe00 cpu=ff09fe00 size=0001fe00
fb1: s3cfb frame buffer device
Window[2] - FB1: map_video_memory: clear ff0c0000:0003fc00
FB1: map_video_memory: dma=5d280000 cpu=ff0c0000 size=0003fc00
fb2: s3cfb frame buffer device
Window[3] - FB1: map_video_memory: clear ff100000:0003fc00
FB1: map_video_memory: dma=5d2c0000 cpu=ff100000 size=0003fc00
fb3: s3cfb frame buffer device
ledsinitialized.
s3c-aes initialized
S3C AES Drvier
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
s3c6400-uart.0: s3c2410_serial0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
s3c6400-uart.1: s3c2410_serial1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
s3c6400-uart.2: s3c2410_serial2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
s3c6400-uart.3: s3c2410_serial3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
brd: module loaded
loop: module loaded
nbd: registered device at major 43
pmem: 1 init
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
mcp251x_init(1063): start
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
CSLIP: code copyright 1989 Regents of the University of California.
dm9000 Ethernet Driver
eth0: dm9000 at ce890000,ce890004 IRQ 108 MAC: 00:22:12:34:56:90
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
console [netcon0] enabled
netconsole: network logging started
Linux video capture interface: v2.00
s3c-fimc: controller 0 registered successfully
s3c-fimc: controller 1 registered successfully
S3C6400 MFC Driver, (c) 2007 Samsung Electronics
S3C6400 MFC Driver, (c) 2007 Samsung Electronics
S3C PostProcessor Driver v3.12, (c) 2009 Samsung Electronics
S3C6410 TV encoder Driver, (c) 2008 Samsung Electronics
S3C6410 TV encoder Driver init OK.
S3C6410 TV scaler Driver, (c) 2008 Samsung Electronics
S3C6410 TV scaler Driver init OK.
S3C Rotator Driver, (c) 2008 Samsung Electronics
s3c_rotator_probe called
s3c_rotator_probe success
S3C JPEG Driver, (c) 2007 Samsung Electronics
s3c-g2d: Driver loaded succesfully
s3c-g2d: Module initialized.
s3c-g3d: Driver loaded succesfully
s3c-g3d: Module initialized.
S3C CMM Driver, (c) 2008 Samsung Electronics
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
Creating 2 MTD partitions on "NAND 1GiB 3,3V 8-bit":
0x00400000-0x00800000 : "cramfs"
0x00800000-0x40000000 : "ubifs"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 262144 bytes (256 KiB)
UBI: logical eraseblock size: 258048 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "ubifs"
UBI: MTD device size: 1016 MiB
UBI: number of good PEBs: 4064
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 4064
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 2/1
UBI: background thread "ubi_bgt0d" started, PID 1053
spi->irq = 151
Max,Min-Speed [33333333, 130208]Hz
Irq=80
IOmem=[0x7f00bfff-0x7f00b000]
DMA=[Rx-33, Tx-34]
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 79, io mem 0x74300000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
android adb driver
Registered gadget driver 'android_adb'
mice: PS/2 mouse device common for all mice
gpio-keys init
input: gpio-keys as /devices/platform/gpio-keys/input/input0
S3C Touchscreen driver, (c) 2008 Samsung Electronics
S3C TouchScreen got loaded successfully : 12 bits
input: S3C TouchScreen as /devices/virtual/input/input1
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410_rtc: tick irq 34, alarm irq 92
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 378 KHz
[CAMERA]camera_attach_adapter.
parent clock for camera: 266.666 MHz, divisor: 11
parent clock for camera: 266.666 MHz, divisor: 11
parent clock for camera: 266.666 MHz, divisor: 9
CAMERA TVP5150 attached successfully
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
at24 0-0050: 1024 byte 24c08 EEPROM (writable)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (44333333 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
sdhci: card inserted.
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (44333333 Hz)
sdhci: card removed.
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
ASoC version 0.13.2
usb 1-1: new low speed USB device using s3c2410-ohci and address 2
WM9713/WM9714 SoC Audio Codec 0.15
playback: 1, capture : 1
asoc: AC97 HiFi <-> s3c64xx-ac97 mapping ok
[WM9713]Open speaker volume.
ALSA device list:
#0: SMDK6400 (WM9713)
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20081130 abi 8)
NET: Registered protocol family 29
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
s3c2410-rtc s3c2410-rtc: setting system clock to 2011-02-15 19:51:13 UTC (1297799473)
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 1034514432 bytes (1010268 KiB, 986 MiB, 4009 LEBs)
UBIFS: journal size: 33546240 bytes (32760 KiB, 31 MiB, 130 LEBs)
UBIFS: media format: 4 (latest is 4)
UBIFS: default compressor: LZO
UBIFS: reserved for root: 5182151 bytes (5060 KiB)
VFS: Mounted root (ubifs filesystem).
Freeing init memory: 152K
Failed to execute /init. Attempting defaults...
下面是usb鼠标被识别，但是不能用的过程。
usb 1-1: configuration #1 chosen from 1 choice
input: PIXART USB OPTICAL MOUSE as /devices/platform/s3c2410-ohci/usb1/1-1/1-1:1.0/input/input2
generic-usb 0003:093A:2510.0001: input: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-s3c24xx-1/input0
Try to bring eth0 interface up......eth0: link down
Done
Now,starting the qtopia-2.2.0....
Please press Enter to activate this console. Mouse type USB:/dev/input/mice unsupported
Warning: could not register server
usb 1-1: USB disconnect, address 2
usb 1-1: new low speed USB device using s3c2410-ohci and address 3
usb 1-1: configuration #1 chosen from 1 choice
input: PIXART USB OPTICAL MOUSE as /devices/platform/s3c2410-ohci/usb1/1-1/1-1:1.0/input/input3
generic-usb 0003:093A:2510.0002: input: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-s3c24xx-1/input0
usb 1-1: USB disconnect, address 3
usb 1-1: new low speed USB device using s3c2410-ohci and address 4
usb 1-1: configuration #1 chosen from 1 choice
input: PIXART USB OPTICAL MOUSE as /devices/platform/s3c2410-ohci/usb1/1-1/1-1:1.0/input/input4
generic-usb 0003:093A:2510.0003: input: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-s3c24xx-1/input0
