/******************************************************************************* * I.MX6 U-boot PWM hacking * 说明: * 本文主要记录I.MX6 U-boot是如何配置PWM,发现文中的pwm0对应的引脚和真正的 * 电路板的pwm0不是一个,也就意味着其实是引脚连接错了,另外之前一直有一个 * 疑问:为什么双屏显示的时候,有一个屏在U-boot阶段和Kernel阶段总是不亮。原因 * 应该是这里只初始化了一个显示控制部分,也就是不会初始两个PWM。 * * 2016-3-7 深圳 南山平山村 曾剑锋 ******************************************************************************/ cat bootable/bootloader/uboot-imx/board/freescale/mx6q_sabresd/mx6q_sabresd.c ...... #ifdef CONFIG_LCD void lcd_enable(void) { ...... imx_pwm_config(pwm0, 25000, 50000); ------------+ imx_pwm_enable(pwm0); ------------*-+ | | #if defined CONFIG_MX6Q | | /* PWM backlight */ | | mxc_iomux_v3_setup_pad(MX6Q_PAD_SD1_DAT3__PWM1_PWMO); | | /* LVDS panel CABC_EN0 */ | | mxc_iomux_v3_setup_pad(MX6Q_PAD_NANDF_CS2__GPIO_6_15); | | /* LVDS panel CABC_EN1 */ | | mxc_iomux_v3_setup_pad(MX6Q_PAD_NANDF_CS3__GPIO_6_16); | | #elif defined CONFIG_MX6DL | | /* PWM backlight */ | | mxc_iomux_v3_setup_pad(MX6DL_PAD_SD1_DAT3__PWM1_PWMO); | | /* LVDS panel CABC_EN0 */ | | mxc_iomux_v3_setup_pad(MX6DL_PAD_NANDF_CS2__GPIO_6_15); | | /* LVDS panel CABC_EN1 */ | | mxc_iomux_v3_setup_pad(MX6DL_PAD_NANDF_CS3__GPIO_6_16); | | #endif | | ...... | | } | | ...... | | | | static struct pwm_device pwm0 = { <-----------+ | .pwm_id = 0, | | .pwmo_invert = 0, | | }; | | | | | | int imx_pwm_config(struct pwm_device pwm, int duty_ns, int period_ns) <----+ | { | unsigned long long c; | unsigned long period_cycles, duty_cycles, prescale; | u32 cr; | | if (period_ns == 0 || duty_ns > period_ns) | return -1; | | pwm.mmio_base = pwm.pwm_id ? (unsigned long)IMX_PWM2_BASE: | (unsigned long)IMX_PWM1_BASE; | | if (pwm.pwmo_invert) | duty_ns = period_ns - duty_ns; | | c = mxc_get_clock(MXC_IPG_PERCLK); | c = c * period_ns; | do_div(c, 1000000000); | period_cycles = c; | | prescale = period_cycles / 0x10000 + 1; | | period_cycles /= prescale; | c = (unsigned long long)period_cycles * duty_ns; | do_div(c, period_ns); | duty_cycles = c; | | writel(duty_cycles, pwm.mmio_base + MX_PWMSAR); | writel(period_cycles, pwm.mmio_base + MX_PWMPR); | | cr = MX_PWMCR_PRESCALER(prescale) | | MX_PWMCR_STOPEN | MX_PWMCR_DOZEEN | | MX_PWMCR_WAITEN | MX_PWMCR_DBGEN; | | cr |= MX_PWMCR_CLKSRC_IPG_HIGH; | | writel(cr, pwm.mmio_base + MX_PWMCR); | | return 0; | } | | int imx_pwm_enable(struct pwm_device pwm) <----------------+ { unsigned long reg; int rc = 0; if (pwm.enable_pwm_clk) pwm.enable_pwm_clk(); pwm.mmio_base = pwm.pwm_id ? (unsigned long)IMX_PWM2_BASE: (unsigned long)IMX_PWM1_BASE; reg = readl(pwm.mmio_base + MX_PWMCR); reg |= MX_PWMCR_EN; writel(reg, pwm.mmio_base + MX_PWMCR); if (pwm.enable_pwm_pad) pwm.enable_pwm_pad(); return rc; }