svn安装
1、首先下载软件包,我是在weindows上下载后上传到linux下的(可以使用rz命令)
下载地址:http://download.csdn.net/detail/cyteven/6679121
1、安装zlib
tar zvxf zlib-1.2.5.1.tar.gz
cd zlib-1.2.5.1
./configure --prefix=/usr/local/zlib
make
make install’
2、安装openssl
tar zvxf openssl-0.9.8l.tar.gz
cd cd openssl-0.9.8l
./config --prefix=/usr/local/ssl-0.9.8l shared zlib-dynamic enable-camellia
./config -t
make depend
make
make test
make install
cd /usr/local
ln -s ssl-0.9.8l ssl
vi /etc/ld.so.conf
加入如下内容:
/usr/local/ssl/lib
ldconfig
vi /root/.bash_profile
若原来没有安装openssl的旧版本,则放在PATH中的任何位置都可以,但是记住要用冒号分隔开,而不是分号分隔,详见后面的截图,若想查看当前的PATH环境变量都设置了什么,可以使用如下的命令实现
cd /root/
source .bash_profile
echo $PATH
可以查看修改后效果
验证:
ldd /usr/local/ssl/bin/openssl
3、安装sqllite
tar -zvxf sqlite-autoconf-3071502.tar.gz
cd sqlite-autoconf-3071502
./configure --prefix=/usr/local/sqlite
make
make install
4、安装expat
tar zvxf expat-2.1.0.tar.gz
cd expat-2.1.0/
./configure --prefix=/usr/local/expat
make
make install
echo /usr/local/lib >> /etc/ld.so.conf
ldconfig
5、开始安装apr
tar zvxf apr-1.4.6.tar.gz //解压
cd apr-1.4.6/
./configure --prefix=/usr/local/apr
make
make install
6、开始安装apr-util
cd apr-util-1.4.1/
../configure --prefix=/usr/local/apr-util --with-apr=/usr/local/apr/
make
make install
echo /usr/local/apr-util/lib/ >> /etc/ld.so.conf
7、安装neon
tar zvxf neon-0.30.0.tar.gz
./configure --prefix=/usr/local/neon --enable-shared
make
make install
8、安装svn
tar -zvxf subversion-1.5.0.tar.gz
tar zvxf subversion-deps-1.5.0-rc5.tar.gz
cp -ri subversion-1.5.0-rc5/* subversion-1.5.0
cd subversion-1.5.0
./configure --prefix=/usr/local/svn -with-apr=/usr/local/apr -with-apr-util=/usr/local/apr-util/ -with-neon= -with-zlib=/usr/local/zlib/ --with-ssl
make
make install
9、验证
cd /usr/local/svn/bin
./svn --version
11、哈哈成功了(现在可以正常使用svn并且可以正确更新http的站点)
之前一直遇到错误:
前面两个,是subversion编译的默认模块,ra_dav是大多数人遇到的问题。如果ra_dav没有编译到系统中,当你从http://这样的路径checkout时,会出现这样的错误提示:svn: Unrecognized URL scheme
环境变量配置
添加环境变量:
export PATH="$PATH:/usr/local/svn/bin"
这个地方可以执行export指令来验证一下是否配置成功
已经加入到了环境变量,快去验证一下吧
测试SVN是否安装成功,去任意目录执行:
svnserve --version
如果显示版本信息, 则安装成功.
QA:常见问题
1、configure: error: no XML parser was found: expat or libxml 2.x required 安装noen时候报错
下载 libxml2-devel-2.6.26-2.1.2.8.i386.rpm 和zlib-devel-1.2.3-3.i386.rpm安装包
rpm -ivh zlib-devel-1.2.3-3.i386.rpm
rpm -ivh libxml2-devel-2.6.26-2.1.2.8.i386.rpm
安装后就完美解决了上面的问题
2、checking for library containing RSA_new... not found
发现openssl没有找到 我们来安装一下这个东东
下载个openssl-devel-0.9.8e-12.el5.i386.rpm
rpm -ivh openssl-devel-0.9.8e-12.el5.i386.rpm
又有报错krb5-devel-1.6.1-36.el5.i386 is needed by openssl-devel-0.9.8e-12.el5.i386
下载krb5-devel-1.6.1-36.el5.i386安装之
rpm -ivh krb5-devel-1.6.1-36.el5.i386.rpm
汗,又有一堆报错:
e2fsprogs-devel is needed by krb5-devel-1.6.1-36.el5.i386
keyutils-libs-devel is needed by krb5-devel-1.6.1-36.el5.i386
libselinux-devel is needed by krb5-devel-1.6.1-36.el5.i386
不过没关系,因为我们能看出来是什么问题那就继续下载之安装之前两个安装ok发下最后一个又报错了
libsepol-devel >= 1.15.2-1 is needed by libselinux-devel-1.33.4-5.5.el5.i386
看来已经看到希望了
下载libsepol-devel-1.15.2-2.el5.i386.rpm
安装之
rpm -ivh libsepol-devel-1.15.2-2.el5.i386.rpm
ok了这回从下面一次安装上去,嗯完美解决了
本来以为完全ok又遇到如下问题:
cannot restore segment prot after reloc: Permission denied
make:***[revision-install] 错误 127
编辑/etc/selinux/config,找到这段:
# This file controls the state of SELinux on the system.
# SELINUX= can take one of these three values:
# enforcing - SELinux security policy is enforced.
# permissive - SELinux prints warnings instead of enforcing.
# disabled - SELinux is fully disabled.
SELINUX=enforcing
把 SELINUX=enforcing 注释掉:#SELINUX=enforcing ,然后新加一行为:
SELINUX=disabled
保存,关闭。
......
编辑/etc/sysconfig/selinux,找到:
# This file controls the state of SELinux on the system.
# SELINUX= can take one of these three values:
# enforcing - SELinux security policy is enforced.
# permissive - SELinux prints warnings instead of enforcing.
# disabled - SELinux is fully disabled.
SELINUX=enforcing
如果SELINUX已经是 SELINUX=disabled,那么就不用改了,否则就把SELINUX=enforcing 注释掉,新加一行:
SELINUX=disabled
保存,退出。
上面都执行过了还是不行 泪奔
chcon -t texrel_shlib_t /usr/software/svn/subversion-1.5.0/subversion/libsvn_subr/.libs/libsvn_subr-1.so/usr/software/svn/subversion-1.5.0/subversion/libsvn_subr/.libs/libsvn_subr-1.so
也不行
最后发现原来执行这个就ok了:
/usr/sbin/setenforce 0