Arduino 各种模块篇 蓝牙模块 手机蓝牙控制Arduino LED灯

时间：2022-08-14 22:26:28

解决方案。

条件：

1.手机android 商店下载 blueTerm

2.向arduino中载入如下代码：

char val;
int ledpin=13;
void setup()
{
  Serial.begin(9600);
  pinMode(ledpin,OUTPUT);
}
 
void loop()
{
  val=Serial.read();
  if(val=='o')
  {
    digitalWrite(ledpin,HIGH);
    Serial.println("LED ON!");
  }else if(val=='f'){
  digitalWrite(ledpin,LOW);
Serial.println("LED OFF!");
  }
}

3. 将蓝牙模块的RxD链接到arduino的Tx口上，蓝牙的TxD链接到arduino的Rx口上。

Arduino 各种模块篇 蓝牙模块 手机蓝牙控制Arduino LED灯

4. 打开android的blueTerm ，链接到蓝牙，默认密码1234。

链接上，在手机上输入，o

led灯亮。

键入f

led灭。

 

挺简单的。

——————————————————————————————————————

如果想把蓝牙放到别的口上，不占用Pin1,2 arduino与计算机默认的串口。

那就用下面的方法，模拟一个serial port， 比如说用Pin6,7 与单片机通讯。

下面的代码做参考使用：

http://arduinobasics.blogspot.com/2013/01/arduino-basics-bluetooth-tutorial.html

/* This project combines the code from a few different sources.
This project was put together by ScottC on the 15/01/2013
http://arduinobasics.blogspot.com/

Bluetooth slave code by Steve Chang - downloaded from :
http://www.seeedstudio.com/wiki/index.php?title=Bluetooth_Shield

Grove Chainable RGB code can be found here :
http://www.seeedstudio.com/wiki/Grove_-_Chainable_RGB_LED#Introduction

*/
 
#include <SoftwareSerial.h> //Software Serial Port

#define uint8 unsigned char 
#define uint16 unsigned int
#define uint32 unsigned long int

#define RxD 6 // This is the pin that the Bluetooth (BT_TX) will transmit to the Arduino (RxD)
#define TxD 7 // This is the pin that the Bluetooth (BT_RX) will receive from the Arduino (TxD)
 
#define DEBUG_ENABLED 1


int Clkpin = 9; //RGB LED Clock Pin (Digital 9)
int Datapin = 8; //RGB LED Data Pin (Digital 8)
 
SoftwareSerial blueToothSerial(RxD,TxD);

/*----------------------SETUP----------------------------*/ 
void setup() { 
 Serial.begin(9600); // Allow Serial communication via USB cable to computer (if required)
 pinMode(RxD, INPUT); // Setup the Arduino to receive INPUT from the bluetooth shield on Digital Pin 6
 pinMode(TxD, OUTPUT); // Setup the Arduino to send data (OUTPUT) to the bluetooth shield on Digital Pin 7
 pinMode(13,OUTPUT); // Use onboard LED if required.
 setupBlueToothConnection(); //Used to initialise the Bluetooth shield
 
 pinMode(Datapin, OUTPUT); // Setup the RGB LED Data Pin
 pinMode(Clkpin, OUTPUT); // Setup the RGB LED Clock pin
 
} 

/*----------------------LOOP----------------------------*/ 
void loop() { 
 digitalWrite(13,LOW); //Turn off the onboard Arduino LED
 char recvChar;
 while(1){
 if(blueToothSerial.available()){//check if there's any data sent from the remote bluetooth shield
 recvChar = blueToothSerial.read();
 Serial.print(recvChar); // Print the character received to the Serial Monitor (if required)
 
 //If the character received = 'r' , then change the RGB led to display a RED colour
 if(recvChar=='r'){
 Send32Zero(); // begin
 DataDealWithAndSend(255, 0, 0); // first node data
 Send32Zero(); // send to update data 
 }
 
 //If the character received = 'g' , then change the RGB led to display a GREEN colour
 if(recvChar=='g'){
 Send32Zero(); // begin
 DataDealWithAndSend(0, 255, 0); // first node data
 Send32Zero(); // send to update data 
 }
 
 //If the character received = 'b' , then change the RGB led to display a BLUE colour
 if(recvChar=='b'){
 Send32Zero(); // begin
 DataDealWithAndSend(0, 0, 255); // first node data
 Send32Zero(); // send to update data 
 }
 }
 
 //You can use the following code to deal with any information coming from the Computer (serial monitor)
 if(Serial.available()){
 recvChar = Serial.read();
 
 //This will send value obtained (recvChar) to the phone. The value will be displayed on the phone.
 blueToothSerial.print(recvChar);
 }
 }
} 


//The following code is necessary to setup the bluetooth shield ------copy and paste----------------
void setupBlueToothConnection()
{
 blueToothSerial.begin(38400); //Set BluetoothBee BaudRate to default baud rate 38400
 blueToothSerial.print("\r\n+STWMOD=0\r\n"); //set the bluetooth work in slave mode
 blueToothSerial.print("\r\n+STNA=SeeedBTSlave\r\n"); //set the bluetooth name as "SeeedBTSlave"
 blueToothSerial.print("\r\n+STOAUT=1\r\n"); // Permit Paired device to connect me
 blueToothSerial.print("\r\n+STAUTO=0\r\n"); // Auto-connection should be forbidden here
 delay(2000); // This delay is required.
 blueToothSerial.print("\r\n+INQ=1\r\n"); //make the slave bluetooth inquirable 
 Serial.println("The slave bluetooth is inquirable!");
 delay(2000); // This delay is required.
 blueToothSerial.flush();
}


//The following code snippets are used update the colour of the RGB LED-----copy and paste------------
void ClkProduce(void){
 digitalWrite(Clkpin, LOW);
 delayMicroseconds(20); 
 digitalWrite(Clkpin, HIGH);
 delayMicroseconds(20); 
}
 
void Send32Zero(void){
 unsigned char i;
 for (i=0; i<32; i++){
 digitalWrite(Datapin, LOW);
 ClkProduce();
 }
}
 
uint8 TakeAntiCode(uint8 dat){
 uint8 tmp = 0;
 if ((dat & 0x80) == 0){
 tmp |= 0x02; 
 }
 
 if ((dat & 0x40) == 0){
 tmp |= 0x01; 
 }
 
 return tmp;
}
 
// gray data
void DatSend(uint32 dx){
 uint8 i;
 for (i=0; i<32; i++){
 if ((dx & 0x80000000) != 0){
 digitalWrite(Datapin, HIGH);
 } else {
 digitalWrite(Datapin, LOW);
 }
 
 dx <<= 1;
 ClkProduce();
 }
}
 
// data processing
void DataDealWithAndSend(uint8 r, uint8 g, uint8 b){
 uint32 dx = 0;
 
 dx |= (uint32)0x03 << 30; // highest two bits 1，flag bits
 dx |= (uint32)TakeAntiCode(b) << 28;
 dx |= (uint32)TakeAntiCode(g) << 26; 
 dx |= (uint32)TakeAntiCode(r) << 24;
 
 dx |= (uint32)b << 16;
 dx |= (uint32)g << 8;
 dx |= r;
 
 DatSend(dx);
}

Please take good notice of the references blow of the link which I give you above.

No third lib required. Only original one.

 

***********************************************************************

Also here's another project about how to control arduino widgets via bluetooth protocol.

Bluetooth , motor, android, arduino

http://www.instructables.com/id/Arduino-Control-DC-Motor-via-Bluetooth/step3/Arduino-Code/

 

 

标签：

相关文章